Supero AS-1011M-UR User Manual Download

Page: 68 / 104

6-6

AS1011M-UR User's Manual

SAS/SATA Drive Installation

Mounting a SAS/SATA drive in a drive carrier

The SAS/SATA drives are mounted in drive carriers to simplify their installation

and removal from the chassis. These carriers also help promote proper airfl ow for

the drive bays. For this reason, even empty carriers without drives installed must

remain in the chassis. To add a new drive, install a drive into the carrier with the

printed circuit board side facing down so that the mounting holes align with those

in the carrier. Secure the drive to the carrier with six screws, as shown in Figure

6-4.

Figure 6-4. Mounting a SAS/SATA Drive in a Carrier

Important: Regardless of how many SAS/SATA drives are in-

stalled, all drive carriers must remain in the drive bays to maintain

proper airfl ow.

Use caution when working around the SAS/SATA backplane. Do

not touch the backplane with any metal objects and make sure no

ribbon cables touch the backplane or obstruct the holes, which

aid in proper airfl ow.

Summary of Contents for AS-1011M-UR









































































































Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands

Supero AS-1011M-UR, User Manual

Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands