Supero AS-1011M-UR User Manual Download

Page: 101 / 104

C-1

Appendix C: System Specifi cations

Appendix C

System Specifi cations

Processors

Single AMD Opteron 1000 processor in AM2 socket

Note: Please refer to our web site for complete details on supported processors.

Chipset

nVidia MCP55 Pro

BIOS

4 Mb AMIBIOS

LPC Flash ROM

Memory Capacity

Four dual/single channel DIMM slots supporting up to 8 GB of DDR2-800/667/533

unbuffered

ECC/non-ECC

SDRAM.

See the memory section in Chapter 5 for details.

SATA Controller

On-chip (MCP55) controller for Serial ATA

SAS/SATA Drive Bays

Four (4) hot-swap drive bays to house four (4) SAS or SATA drives

Peripheral Drive Bays

One (1) slim DVD-ROM drive

Expansion Slots

(provided with included riser cards)

Right side: one PCI-E x8 card

Left side: one UIO card and one PCI-E x8 card. (See section 5-7 for details)

Motherboard

H8SMU (proprietary form factor)

Dimensions: 7.9" x 13" (201 x 330 mm)

Summary of Contents for AS-1011M-UR









































































































Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands

Supero AS-1011M-UR, User Manual

Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands