Supero AS-1011M-UR User Manual Download

Page: 85 / 104

Chapter 7: BIOS

7-13

possibility of Electromagnetic Interference.

PCIE Spread Spectrum

Use this setting to Enable or

Disable

spread spectrum for the PCIE.

SATA Spread Spectrum

Use this setting to

Enable

or Disable spread spectrum for SATA.

Primary Graphics Adapter

Use this setting to select

PCI Express -> PCI

or PCI -> PCI Express for the

primary graphics adapter.

USB 1.1 Controller

Enable

or disable the USB 1.1 controller.

USB 2.0 Controller

Enable

or disable the USB 2.0 controller.

Legacy USB Support

Select "Enabled" to enable the support for USB Legacy. Disable Legacy support

if there are no USB devices installed in the system. "Auto" disabled Legacy

support if no USB devices are connected. The options are Disabled,

Enabled

and Auto.

USB 2.0 Controller Mode

Select the controller mode for your USB ports. Options are

HiSpeed

and

FullSpeed. (HiSpeed=480 Mbps, FullSpeed=12 Mbps

)

BIOS EHCI Hand-Off

Enable

or Disable a workaround for OS's without EHCI hand-off support.

MAC0 LAN0

Settings are

Auto

and Disabled for MAC0 LAN0.

MAC0 LAN0 Bridge

Settings are

Enabled

and Disabled for MAC0 LAN0 bridge.

MAC1 LAN1

Settings are

Auto

and Disabled for MAC1 LAN1.

Summary of Contents for AS-1011M-UR









































































































Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands

Supero AS-1011M-UR, User Manual

Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands