Supero AS-1011M-UR User Manual Download

Page: 76 / 104

7-4

AS1011M-UR User's Manual

ACPI HPET Table

Use this setting to

Enable

or Disable the ACPI HPET Table.

Power Button Mode

Allows the user to change the function of the power button. Options are

On/Off

and Suspend.

Restore on AC Power Loss

This setting allows you to choose how the system will react when power returns

after an unexpected loss of power. The options are Power Off, Power On and

Last State

Watch Dog Timer

This setting is used to Enable or

Disable

the Watch Dog Timer function. It must

be used in conjunction with the Watch Dog jumper (see Chapter 2 for details).

MPS Revision

This setting allows the user to select the MPS revision level to 1.1 or

1.4.

Smbios Confi guration

This setting is used to Enable or Disable the SMBIOS SMI support.

The options

are

Enabled

and Disabled.

CPU Confi guration

GART Error Reporting

This setting is used for testing only.

MTRR Mapping

This determines the method used for programming CPU MTRRs when 4 GB or

more memory is present. The options are

Continuous

, which makes the PCI

hole non-cacheable, and Discrete, which places the PCI hole below the 4 GB

boundary.

Power Now

This setting is used to Enable or

Disable

the AMD Power Now feature.

Summary of Contents for AS-1011M-UR









































































































Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands

Supero AS-1011M-UR, User Manual

Search results

Summary of Contents for AS-1011M-UR

Reviews:

Related manuals for AS-1011M-UR

Brands by name

Popular brands