Supermicro SuperServer SYS-2049U-TR4 User Manual Download Page 56 | Manualshive

Page: 56 / 151

background image

56

SuperServer SYS-2049U-TR4 User's Manual

Chapter 4

Motherboard Connections

This section describes the connections on the motherboard and provides pinout definitions.
Note that depending on how the system is configured, not all connections are required.

The LEDs on the motherboard are also described here. A motherboard layout indicating
component locations may be found in Chapter 1.
Please review the Safety Precautions in Chapter 3 before installing or removing components.

4.1 Power Connections

Power Supply Unit Connectors

Two main power supply unit connectors (PSU1/PSU2) are located on J24/J25 on the
motherboard. Connect these connectors to your power supply to provide power to your
system. See the layout drawing below for the locations of PSU1 and PSU2.

12V 8-pin CPU Power Connectors

In addition to the main power supply units, there are seven 8-pin 12V DC power connectors
located on the motherboard. Four of these 8-pin power connectors (JPWR1-JPWR4) are
used for GPU devices, and the remaining three (JPWR5-JPWR7) are used for backplane
devices. Additionally, J12VSB, located between PSU1/PSU2, provides 12V standby power

to the system. Refer to the tables below for pin definitions.

GPU Power (JPWR1-4)

Pin Definitions

Pin#

Definition

1 - 4 Ground
5 - 8 +12V

Back Panel Power (JPWR5-7)

Pin Definitions

Pin#

Definition

1 - 4 Ground
5 - 6 +12V
7 - 8 +5V

«
...
54
55
56
57
58
...
»

Summary of Contents for SuperServer SYS-2049U-TR4
























































































































































Reviews:

No comments

Related manuals for SuperServer SYS-2049U-TR4

Brand: D-Link Pages: 12

System x3100 M4

Brand: IBM Pages: 332

Flex System p270 Compute Node

Brand: IBM Pages: 510

Brand: Patton electronics Pages: 326

Brand: Vxl Pages: 19

SUPERSERVER 5015M-NT

Brand: Supero Pages: 134

Brand: Kraun Pages: 36

Brand: D-Link Pages: 32

Brand: D-Link Pages: 22

DP-313 - Air 802.11b Wireless Print Server

Brand: D-Link Pages: 28

Brand: D-Link Pages: 64

D DP-301P+ DP-301P+

Brand: D-Link Pages: 2

Brand: D-Link Pages: 100

AirPlus G DP-G301

Brand: D-Link Pages: 88

Brand: D-Link Pages: 37

Brand: D-Link Pages: 2

Brand: D-Link Pages: 69

AirPlus DP-G321

Brand: D-Link Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands