Supermicro SuperServer SYS-2049U-TR4 User Manual Download Page 45

Page: 45 / 151

Chapter 3: Maintenance and Component Installation

Installing External PCI Expansion Cards

1. Power down the system and remove the top chassis cover.

Remove the Ultra riser bracket or WIO riser bracket by flipping up its riser cage release

tab as pictured in Figures 3-5.

3. Insert the expansion card(s) into the riser card slot(s).

4. Reinstall the riser card into the motherboard expansion slot while aligning the bracket

into the chassis. Flip down the riser cage release tab.

5. Replace the chassis cover.

Figure 3-5. Riser Cage Release Tabs

Ultra Riser Cage Release Tab

WIO Riser Cage Release Tab

Summary of Contents for SuperServer SYS-2049U-TR4
























































































































































Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands

Supermicro SuperServer SYS-2049U-TR4, User Manual

Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands