Supermicro SuperServer SYS-2049U-TR4 User Manual Download Page 104

Page: 104 / 151

SuperServer SYS-2049U-TR4 User's Manual

104

6.5 IPMI

Use this feature to configure Intelligent Platform Management Interface (IPMI) settings.

When you select this submenu and press the <Enter> key, the following information will
display:

•

IPMI Firmware Revision: This feature indicates the IPMI firmware revision used in your

system.

•

Status of BMC: This feature indicates the status of the BMC (Baseboard Management
Controller) installed in your system.



System Event Log

Enabling/Disabling Options

SEL Components

Select Enabled for all system event logging at bootup. The options are

Enabled

and Disabled.

Summary of Contents for SuperServer SYS-2049U-TR4
























































































































































Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands

Supermicro SuperServer SYS-2049U-TR4, User Manual

Search results

Summary of Contents for SuperServer SYS-2049U-TR4

Reviews:

Related manuals for SuperServer SYS-2049U-TR4

Brands by name

Popular brands