Supermicro 7048R-C1R, User Manual

Page: 35 / 79

Chapter 5: Advanced Serverboard Setup
5-13 5-12
S
UPER
S
ERVER 7048R-C1RT/7048R-C1R User's Manual
Jumper Description Default Setting
JBT1 Clear CMOS See Section 5-8
JI
2
C1/JI
2
C2 SMB to PCI-E Slots Enable/Disable Pins 2-3 (Disabled)
JPB1 BMC Enable/Disable Pins 1-2 (Enabled)
JPG1 VGA Enable/Disable Pins 1-2 (Enabled)
JPL1 LAN Ports Enable/Disable Pins 1-2 (Enabled)
JPME2 Manufacture (ME) Mode Select Pins 1-2 (Normal)
JWD1 Watch Dog Timer Pins 1-2 (Reset)
JPS1 SAS Enable/Disable Pins 1-2 (Enabled)
Connector Description
COM1/COM2 Backplane COM Port1/Front accessible COM2 header
FAN1-6,A, B CPU/system Fan Headers
J24 24-pin ATX Main Power Connector
JD1 Speaker/Power LED Header
JF1 Front Panel Control Header
JIPMB1 4-pin External BMC I
2
C Header (for IPMI card)
JL1 Chassis Intrusion Header
JPI
2
C1 Power Supply SMBbus I
2
C Header
JPWR1/JPWR2 12V 8-pin Power Connectors
JSTBY1 Standby Power Connector
JTPM1 TPM (Trusted Platform Module)/Port 80 Header
LAN1/LAN2 Gb Ethernet (GLAN) ports 1/2 (X10DRH-C)
10Gb Ethernet (TLAN) ports 1/2 (X10DRH-CT)
IPMI LAN Dedicated IPMI LAN Port
I-SATA 0-5 SATA 3.0 Ports supported by Intel PCH (I-SATA 0-5)
S-SATA SATA 3.0 Vertical Connector w/4-SATA Ports supported by Intel
SCU
SAS(0-3,4-7) SAS 3.0 Ports (0-3,4-7) supported by the LSI 3108
(I-)SGPIO1/2 Serial Link General Purpose I/O Headers 1/2 for SATA ports (I-
SGPIO1 for I-SATA0-3, I-SGPIO2 for I-SATA4/5)
UID UID (Unit Identification) Switch
USB 0/1 Backpanel USB 2.0 Ports 0/1
USB 2/3 Front accessible USB 2.0 Headers
USB 4/5 Backpanel USB 3.0 Ports
USB 6 Front Accessible Type A 3.0 Connector
USB 7/8 Front Accessible USB 3.0 Header
5-7 Connector Definitions
Power Connectors
A 24-pin main power supply connector
(J24), and two 8-pin CPU power connectors
(JPWR1/JPWR2) are located on the
serverboard. These power connectors
meet the SSI EPS 12V specification
and must be connected to your power
supply to provide adequate power to the
system. See the tables on the right for
pin definitions.
Caution : To provide adequate power to
the serverboard, be sure to connect the
24-pin ATX PWR (J24) and the
two 8-pin
power connectors (JPWR1, JPWR2) to the
power supply. Failure to do so may void the
manufacturer warranty on your power supply
and serverboard.
ATX Power 24-pin Connector
Pin Definitions
Pin# Definition Pin # Definition
13 +3.3V 1 +3.3V
14 -12V (NC) 2 +3.3V
15 COM 3 COM
16 PS_ON 4 +5V
17 COM 5 COM
18 COM 6 +5V
19 COM 7 COM
20 Res (NC) 8 PWR_OK
21 +5V 9 5VSB
22 +5V 10 +12V
23 +5V 11 +12V
24 COM 12 +3.3V
Required Connections
12V 8-pin
Power Connector
Pin Definitions
Pins Definition
1 through 4 Ground
5 through 8 +12V