Supermicro 7048R-C1R, User Manual

Page: 7 / 79

1-2 1-3
Chapter 1: Introduction
S
UPER
S
ERVER 7048R-C1RT/7048R-C1R User's Manual
1-2 Serverboard Features
The SuperServer 7048R-C1RT/7048R-C1R is built around the X10DRH-CT/C, a
dual processor serverboard based on the Intel C612 chipset. Below are the main
features of the X10DRH-CT/C. (See Figure 1-1 for a block diagram of the chipset).
Processors
The X10DRH-CT/C supports single or dual Intel® E5-2600 (v3/v4) processors in
Socket R3, LGA 2011 type sockets. Please refer to our website for a complete list-
ing of supported processors (www.supermicro.com).
Memory
The X10DRH-CT/C has 16 DIMM slots that can support up to 2 TB of Load Re-
duced (LRDIMM) ECC registered memory or up to 1 TB of ECC registered (RDIMM)
DDR4-2400/2133/1866/1600 memory. Please refer to Chapter 5 for details on
installing memory.
SAS
An LSI 3108 SAS controller is included on the serverboard to support up to eight
SAS 3.0 ports with RAID 0, 1, 5, 6, 10, 50 and 60.
Note: The SAS drives are hot-swappable units. You must have your RAID set up
to enable the hot-swap capability of the SAS drives. Documentation on RAID setup
guidelines can be found on our website.
SATA
A SATA controller is integrated into the C612 chipset to provide ten SATA 3.0 ports,
with RAID 0, 1, 5 and 10.
Note: The SATA drives are hot-swappable units. You must have your RAID set up
to enable the hot-swap capability of the SATA drives. Documentation on RAID setup
guidelines can be found on our website.
PCI-E Expansion Slots
The X10DRH-CT/C has six PCI-E 3.0 x8 slots and one PCI-E 3.0 x16 slot. Note
that the PCI slots are controlled by the CPUs so only three slots (Slot1-Slot3 ) are
available if both CPUs are not installed on the board at the same time. (CPU1:
Slot1-Slot3, CPU2: Slot4-Slot7.) See Figure 1-1 and the serverboard layout in
Chapter 5 for details.
Rear I/O Ports
The I/O ports include one COM port, a VGA port, two USB 3.0 ports, two USB 2.0
ports, two Gb LAN ports (these are 10 Gb TLAN ports on the X10DRH-CT) and a
dedicated IPMI LAN port
•
X10DRH-C has Gigabit ports
•
X10DRH-CT has 10GBaseT ports
1-3 Server Chassis Features
The following is a general outline of the main features of the SC745TQ-R920B
server chassis.
System Power
The SC745TQ-R920B features a redundant, hot-plug 920W power supply com-
posed of two separate power modules. The power redundancy feature allows you
to replace a failed power supply without shutting down the system.
Front Control Panel
The control panel on the SuperServer 7048R-C1RT/7048R-C1R provides you
with system monitoring and control. LEDs indicate system power, HDD activity,
network activity, system overheat and power supply failure. A main power button
and a system reset button are also included. In addition, two USB ports have been
incorporated into the control panel to provide front side USB access.
Cooling System
The chassis has an innovative cooling design that includes three 8-cm hot-plug
system cooling fans located in the middle section of the chassis as well as two 8-cm
hot-plug exhaust fans located at the rear of the chassis. An air shroud channels the
airflow from the system fans to efficiently cool the processor area of the system.
The power supply module also includes a cooling fan.