background image

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.

14

Glowing Embers

Bag of Glowing 

Embers (rockwool)

Separate into Quarter 

Size (separate) Pieces

     WARNING

DO NOT attempt to install the 
logs until the appliance instal-
lation has been completed, the 
gas line connected and tested 
for leaks and the initial burner 
operation has been checked 
out. 

Figure 26

       

WARNING

This appliance is not designed 
to burn wood.  Any attempt to 
do so could cause irreparable 
damage to appliance and prove 
hazardous to your safety.

       WARNING

If logs are not installed according 
to the log installation instruc-
tions, fl ame impingement and 
improper combustion could 
occur and result in soot and/or 
excessive production of carbon 
monoxide (CO), a colorless, 
odorless, toxic gas.

REFERENCE

Firebox Accessories / Parts

Cat. No.

Model No.

Description

88L53

FGE

Bag of Glowing Embers
(1 oz. rockwool)

80L42

FDVS

Bag of Decorative 
Volcanic Stone

Table 10

      

WARNING

The size and position of the log 
set is critical to achieve a safe, 
reliable and attractive fl ame 
pattern.  Any attempt to use a 
different log set in the fi replace 
will void the warranty and will 
result in incomplete combus-
tion, sooting, and poor fl ame 
quality.

SSBV-4035 - Install as Follows

Carefully position the ceramic fi ber logs into the 
fi rebox as shown in 

Figure 28

.  Logs should be 

placed in the order shown and per the following 
instructions. 

1

. Place embers on the front burner tube and 

volcanic stone in front of the burner as 
shown and per instructions on this Page 
(see

 Placement of Glowing Embers  & Install 

Decorative Volcanic Stone 

on this page).

2

. Place the rear log (A) as shown. Position 

the 2 notches on the bottom of the log over 
the 2 corresponding locating brackets as 
shown.

3

. Place the center log (C) as shown. The 2 

notches on the bottom of the log fi t over 
the corresponding locating brackets.

4

.  Place the top right log (D) as shown. The top 

fork on log (D) fi ts into notch on log (A) as 
shown.  The bottom fork on log (D) rests on 
subfl oor fl ange (identifi ed  in photo #1).

5

. Place the top left log (B) as shown. The top 

fork on log (B) fi ts into notch on log (A).  The 
bottom of the log rests on the subfl oor.

SSBV-3530 - Install as Follows

Carefully position the ceramic fi ber logs into the 
fi rebox as shown in 

Figure 27

.  Logs should be 

placed in the order shown and per the following 
instructions. 

1.

 Place embers on the front burner tube and 

volcanic stone in front of the burner as 
shown and per instructions on this Page 
(see

 Placement of Glowing Embers  & Install 

Decorative Volcanic Stone 

on this Page).

2.

 Place the rear log (A) as shown. Position 

the 2 notches on the bottom of log (A) over 
the 2 corresponding locating brackets as 
shown.

3

. Place the center log (C) as shown. The 2 

notches on the bottom of log (C) fi t over 
the corresponding locating brackets.

4

. Place the left log (B) as shown. The top fork 

on log (B) fi ts into the notch on log (A).  The 
bottom of log (B) rests on the subfl oor.

5

. Place the top fork on log (D) into notch on 

log (A) as shown. The bottom fork on log 
(D) rests on the subfl oor fl ange (identifi ed  
in photo #1).

Step 10. INSTALL VOLCANIC STONE, 
GLOWING EMBERS AND LOGS

1. Remove the front glass enclosure panel 

(see 

Glass Door Panel Removal Instructions 

on 

Page 17

)

.

2. 

Carefully remove the log set box from 
the fi rebox.  Next, remove embers and 
volcanic stone from the control compart-
ment.

   

Handle logs carefully to prevent 

breakage.

3. Install decorative volcanic stone -

 Mound up 

a portion of the volcanic stone in front of the 
burner in a pleasing pattern. 

4.

 

Placement of Glowing Embers - 

  Separate the  Embers (rockwool) into pieces 

about  the size of a quarter (see 

Figure 26)

.  

Keep the pieces fl uffed up, not matted. 

 

Distribute these pieces over the  surface of 
the burner, as shown in 

Figures 27 or 28.

  

Do not use more than is necessary.  Ensure 
that the main burner slots remain uncovered 
by the ember material.

 

Note

: This appliance is provided with enough 

Glowing Embers for several applications, do 
not use all that is in a new bag at one time. For 
best glowing effect, replace the ember material 
annually. 

5. Placement of Logs - 

  The logs have locating notches or slots to 

help ensure that they are properly positioned.   
Proper log placement is critical to prevent 
sooting. 

f i r e - p a r t s . c o m

Summary of Contents for SSBV-3530CNE

























Reviews: