background image

Superabrasive 

Owner’s Manual Original Language – Lavina 

®

V32G-X/GTX  

14/2019 

 

3

 

 
WARRANTY AND RETURNS 

 

WARRANTY POLICY FOR 

LAVINA® V-32GX 

If  your  warranty  card  is  missing,  contact  your  local  distributor  and  request  a  warranty  card,  or  visit  us  at 
www.superabrasive.com  to  download  one.    The  customer  is  responsible  for  filling  out  the  card  and  mailing  it  to  the 
manufacturer’s  address  as  indicated  on  the  card.    To  ensure  registration  and  activation  of  warranty  coverage,  the 
warranty card must be mailed to the manufacturer within 30 days from date of purchase; failure to do so may void the 
warranty.    Be  sure  to  provide  the  manufacturer  with  all  of  the  information  requested,  and  most  importantly  with  the 
distributor’s name, machine serial number, and purchase date. 
Superabrasive offers a guarantee on LAVINA® vacuums, covering manufacturing and material defects, for a period of 
24 months from the date of purchase, as invoiced by Superabrasive.  The following conditions pertain to this warranty: 
• Applies only to the original owner and is not transferable. • Vacuum must not be dismantled and tampered with in any 
way.  •  This  warranty  does  not  cover  any  failures  or  defects  caused  by  normal  wear  and  tear,  accidental  damage, 
damage during  transport, improper handling, repairs conducted by  an  unauthorized facility (without prior authorization 
by Superabrasive), or operation that is not in compliance with the instructions provided in this manual.  Superabrasive 
denies all responsibility for damages or injuries, to any persons or objects, caused by improper operation of the vacuum 
unit. • This warranty will become invalid in the event that equipment or accessories used on/with the vacuum unit are 
not supplied or approved by Superabrasiv

e. • Covered components proven defective will be repaired or replaced at no 

charge.  •  This  warranty  does  not  apply  to  any  repair  of/to  of  proprietary  parts,  nor  does  it  cover  cleaning  or  general 
maintenance.  •  This  warranty  does  not  apply  to  items  with  aftermarket  alterations,  changes,  or  modifications.  •  This 
warranty is limited to repair or replacement of covered components and reasonable labor expenses. • In the event of a 
warranty  claim,  the  vacuum  unit  must  be  returned  to  Superabrasive,  or  an  authorized  facility,  for  a  warranty 
investigation, and subsequent warranty repair or replacement. • All warranty returns must be shipped freight prepaid. • 
This warranty is in lieu of and excludes every condition of warranty not herein expressly set out and all liability for any 
form of consequential loss or damage is hereby expressly excluded. 
The  above  warranty  conditions  may  be  changed  only  by  Superabrasive.    Superabrasive  reserves  the  right  to  inspect 
and make a final decision on any machine returned under this warranty.  This warranty applies to new, used, and demo 
machines. 
Superabrasive agrees to repair or replace, free of charge, any parts which have failed due to manufacturer or material 
defects.    Repairs  must  only  be  performed  at  authorized  service  facilities  that  have  been  approved  by  Superabrasive.  
Shipping and handling fees associated with warranty claims must be pre-paid by the customer / claimant. 
In the event that a warranty investigation determines that the damage or unit failure is not attributed to manufacturer or 
material defects, all costs associated with the repair of the vacuum will become the direct responsibility of the claimant.  
If payment is not rendered for such services, Superabrasive will assume ownership of the machine and any associated 
parts in possession. 
Superabrasive  does  not  authorize  any  person  or  representative  to make  any  other  warranty,  or  to assume  for  us  any 
liability in connection with the sale and operation of our products. 
The manufacturer is also not liable in the event that the customer fails to submit a Warranty Certificate, fails to follow 
manual instructions, uses non-original spare parts, or fails to service/clean the vacuum regularly and properly 

 
RETURN POLICY FOR LA

VINA® V32GX 

LAVINA® Vacuums may be returned, subject to the following terms: 
• Vacuums may  not  be returned to Superabrasive  Inc. for credit or repair  without prior authorization.   Please contact 
Superabrasive  Inc.  or  your  local  distributor  for  authorization  and  issuance  of  a  return  authorization  number.    This 
number along with the serial number of the vacuum must be included on all packages and correspondences.  Vacuums 
returned without prior authorization will remain property of the sender and Superabrasive Inc. will not be responsible for 
these.  •  No  vacuums  will  be  credited  after  90  days  from  the  date  of  Superabrasive’s  invoice.  •  All  returns  must  be 
shipped freight prepaid.  All returns may be exchanged for other equipment or parts of equal dollar value.  If vacuums 
are not exchanged, they are subject to a fifteen percent (15%) restocking fee 

 

 

 
 
 
 

Summary of Contents for Lavina V32G-X

















































Reviews: