background image

Superabrasive 

Owner’s manual original language – Lavina

®   

LP36 

01/2020 

 

 

 

34 

 

(2)Any warranted part that is scheduled only for regular inspection in the written instructions 
supplied is warranted for the warranty period stated above. Any such part repaired or replaced 
under warranty will be warranted for the remaining warranty period. 

(3)Any warranted part that is scheduled for replacement as required maintenance in the written 
instructions supplied is warranted for the period of time before the first scheduled replacement date 
for that part. If the part fails before the first scheduled replacement, the part will be repaired or 
replaced by Superabrasive Inc. according to subsection (4) below. Any such part repaired or replaced 
under warranty will be warranted for the remainder of the period prior to the first scheduled 
replacement point for the part. 

(4)Repair or replacement of any warranted part under the warranty provisions herein must be 
performed at a warranty station at no charge to the owner. 

(5)Notwithstanding the provisions herein, warranty services or repairs will be provided at all of our 
distribution centers that are franchised to service the subject engines or equipment. 

(6)The SORE owner will not be charged for diagnostic labor that is directly associated with diagnosis 
of a defective, emission-related warranted part, provided that such diagnostic work is performed at a 
warranty station. 

(7)Superabrasive Inc. is liable for damages to other engine or equipment components proximately 
caused by a failure under warranty of any warranted part. 

(8)Throughout the SORE warranty period stated above, Superabrasive Inc. will maintain a supply of 
warranted parts sufficient to meet the expected demand for such parts. 

(9)Any replacement part may be used in the performance of any warranty maintenance or repairs 
and must be provided without charge to the owner. Such use will not reduce the warranty 
obligations of Superabrasive Inc. 

(10)Add-on or modified parts that are not exempted by the Air Resources Board may not be used. 
The use of any non-exempted add-on or modified parts by the ultimate purchaser will be grounds for 
disallowing a warranty claims. Superabrasive Inc. will not be liable to warrant failures of warranted 
parts caused by the use of a non-exempted add-on or modified part. 

WARRANTED PARTS 

The repair or replacement of any warranted part otherwise eligible for warranty coverage may be 
excluded from such warranty coverage if Superabrasive Inc. demonstrates that the SORE has been 
abused, neglected, or improperly maintained, and that such abuse, neglect, or improper 
maintenance was the direct cause of the need for repair or replacement of the part. That 
notwithstanding, any adjustment of a component that has a factory installed, and properly 
operating, adjustment limiting device is still eligible for warranty coverage. The following emission 
warranty parts are covered: 

(1)Catalytic converter 

(2)Fuel system: Carburetor, pressure regulator and fuel lock off 

(3)Ignition system 

(4)Intake system including pre-filter 

(5)Exhaust manifold 

Summary of Contents for LAVINA LP36 Series



































Reviews: