Super SC809LT-780B User Manual Download Page 52

Page: 52 / 60

C-2

SC809 Chassis Manual

Make sure that the backplane is securely and properly installed on the mother-

•

board to prevent damage to the system due to power shortage.

C-3 An Important Note to Users

All images and layouts shown in this user's guide are based upon the latest PCB

•

Revision available at the time of publishing. The card you have received may or
may not look exactly the same as the graphics shown in this manual.

C-4 Introduction to the SAS-809TQ Backplane

The SAS-809TQ backplane has been designed to utilize the most up-to-date tech-
nology available, providing your system with reliable, high-quality performance.

This manual reflects SAS-8009TQ Revision 1.01, the most current release available

at the time of publication. Always refer to the Supermicro Web site at www.supermi-

cro.com for the latest updates, compatible parts and supported configurations.

Summary of Contents for SC809LT-780B





























































Search results

Summary of Contents for SC809LT-780B

Reviews:

Related manuals for SC809LT-780B

Brands by name

Popular brands

Super SC809LT-780B, User Manual

Search results

Summary of Contents for SC809LT-780B

Reviews:

Related manuals for SC809LT-780B

Brands by name

Popular brands