background image

 

11 

 

 

TRANSFORM unit 
deactivates. 

 

On reaching the set required temperature, the 
TRANSFORM unit switches off automatically. Check 
manual setting of the required temperature as well as the 
TIMER setting. 

How is the m² or 
m³ data of the 
manufacturer 
calculated  

 

The m² or m³ data of the manufacturer for the various 
TRANSFORM units are average values related to a 
room height of 2.5 metres. It must be considered that 
such data can be clearly underscored or exceeded 
under certain circumstances. Circumstances which work 
against efficiency of the TRANSFORM units include e.g. 
bad insulation of the building, large window areas, south 
facing, attic apartment, many additional heat sources, 
such as e.g. number of persons, EDP, light, kitchen 
units, washing units etc.  

TRANSFORM unit 
does not cool 
correctly 

 

You achieve the most effective and economical cooling 
comfort if you already cool the room to be cooled when 
the room temperature is not yet heated up. Air 
conditioners operate more effectively if the temperature 
is to be maintained. To drastically cool the air and 
inventory in a fully heated room requires much more time 
and energy.  

E1 

Room temperature 
outside the function 
range: 
 
Room temperature 
inside the function 
range:
 

Observe all data in these operating instructions 
concerning function range.  
 
Temporary error of start temperature. Please switch the 
TRANSFORM unit off and start it again after approx. 30 
minutes. If the error occurs continuously, the 
TRANSFORM unit requires specialist inspection. 

E2 

Temperature of the 
cooling agent lines too 
high or too low 

Temporary error on measuring output temperature. 
Please switch the TRANSFORM unit off and start it 
again after approx. 30 minutes. If the error occurs 
continuously, the TRANSFORM unit requires specialist 
inspection. 

E3 

Incorrect signal 

This error message in the cooling function refers to too 
high ambient temperatures and in the heating function to 
too low ambient temperatures. Please observe the 
instructions relating to ideal operation of the 
TRANSFORM unit. This may also be a temporary error 
measurement between the start and output temperature. 
Please switch the TRANSFORM unit off and start it 
again after approx. 30 minutes. If the error occurs 
continuously, the TRANSFORM unit requires specialist 
inspection. 

E4 

Water tank full 

If the water tank is full, the warning sign "E4" appears in 
the display. To restart operation of the TRANSFORM 
unit, please remove the plug of the condensation water 
outlet to allow water to leak out. Please use an 
appropriate collection tank. When the water has been 
completely removed, please start the TRANSPORT unit 
again. The TRANSFORM unit can now be used as 
usual. 

DF 

De-icing mode 

This procedure is completely normal and protects the 
system from icing and failure. The unit starts 
automatically after approx. 15 minutes again (depending 
on the function setting). This procedure repeats itself 
regularly. 

 
 

SPARE PARTS AND ACCESSORIES SUPPLY (FAST CONVENIENT SUPPLY) 

 
You can obtain spare parts and accessories for your TRANSFORM unit from your local dealer. And  
at our website 

www.suntec-wellness.de

 

you will find further information on individual  

accessory products as well as information on obtaining our spare parts quickly and conveniently. 

Summary of Contents for Klimatronic Transform 10500














Reviews: