SunStar KM-757 User Manual Download Page 2

Page: 2 / 35

Thank you for purchasing our product.

The upgraded KM-757 km-797 Series, built on valuable technology and

experience drawn from years of production of automatic thread trimming sewing

machines, features new FORTUNA AC SERVO automatic thread trimming motor

designed to fully realize the Mechatronics of the sewing machine industry.

This model guarantees to satisfy increasingly growing and

sophisticated needs of the sewing industry by offering diverse functionalities,

excellent performance, remarkable power, enhanced durability and refined design.

Read all instructions in this manual thoroughly before proceeding with operation of the

sewing machine to achieve maximum performance.

Note that specifications of this product may be changed at any time without

prior notice for performance improvement.

SSUUNNSSTTAARR M

MAACCHHIINNEERRYY CCOO..,, LLTTDD..

Best Quality

Best Price

Best Service

Summary of Contents for KM-757




































Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands

SunStar KM-757, User Manual

Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands