SunStar KM-757 User Manual Download Page 10

Page: 10 / 35

Installation

1) Installation of the machine head

Insert the hinge rubber

①

into the table and fix the oil fan into the center of the machine head support rubber B

②

as in Figure 1 and attach it to

the table. After attaching the machine head hinge

③

to the bed, insert it into the hinge rubber

①

and install the sewing machine on the machine

head support rubber A

④

and machine head support head B

②

[Figure 1]

[Figure 2]

2) Installation of knee lifting solenoid and

power switch box

(1) When attaching the power switch box

⑥

, refer to Figure 2 to make

sure that it is placed at the very center of the solenoid bracket.

(2) After attaching the solenoid onto the table, unfasten the screw

④

adjust the center of middle linking bar

①

and the center of solenoid

shaft

②

in parallel position with the lower side of the table

③

. After

the adjustment is over, fasten the screw tightly.
(See Figure 2.): An assembling position diagram can be found inside
the solenoid box.

(3) The presser foot height of the sewing machine can be adjusted after

unfastening the fixing nut

⑤

and then turning the middle linking bar

①

clockwise to raise and counterclockwise to lower. After finishing

the adjustment, tightly fasten the fixing nut

⑤

(4) According to the installation position of knee-lifting solenoid, the

operation noise, operation load and presser foot elevation range may
differ. Please assemble so that the machine will operate smoothly.

Oil fan

Caution

▶

Installation of the machine should be performed by a trained engineer.

▶

Any electrical wiring must be performed by a qualified technician or agent.

▶

The machine weighs over 42kg. At least 2 persons should carry out the installing work.

▶

Plug in after the installation is complete. If the operator mistakenly steps down on the pedal

with the pug in, the machine will start automatically and can cause physical injuries.

▶

Connect the ground (earth) wire. An unstable connection may result in an electric shock or

a malfunction.

▶

Place the belt cover on top of the machine.

▶

Use both hands when bending the machine backwards or returning it to the normal position.

Using only one hand can lead to severe hand injuries due to the weight of the machine.

Summary of Contents for KM-757




































Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands

SunStar KM-757, User Manual

Search results

Summary of Contents for KM-757

Reviews:

Related manuals for KM-757

Brands by name

Popular brands