Sunshine SXJS3018 Manual Download Page 3

 

 

- 1 - 

SXJS3018 DOUBLE-DECK SCISSOR LIFT 

 

   

Safety Note 

  Please  read  this  manual  carefully  before  using  this  machine.  Strictly 

operating  in  accordance  with  the  instructions,  not  free  to  operate.  Only 

trained and qualified staff to operate and use the lift. 

 Make sure the voltage, phase such Technical Parameters on the nameplate 

of  motor  before  installation,  the  power  connection  must  be  done  by  a 

professional  qualified  electrician.  Make  sure  the  motor  turn  to  the  right 

direction. 

  Use  of  equipment  below  10  degree

should  ensure  that  compressed  air 

through the water filter effectively. 

 When the lift works

people and equipment should keep a certain distance, 

no standing above and under the equipment, and the car on lift can not take 

any staff. 

 The weight of the vehicle which by lifting shall not exceed the lifting capacity 

range of the machine. 

 Remove all barrier around and under of platform before working. 

 While  drive  the  car  on,  ensure  that  the  vehicle  centerline  should  coincide 

with the centerline of the lift countertops.. 

  Leveling  should  be  carried  out  on  the  no  loading  platform.  It

s  strictly 

prohibited to open the balancing valve while the car on the platform. 

 Equipment no working or overnight for long period, it should reduce to the 

lowest position, and drive away the vehicle, then cut off the power. 

 

Summary of Contents for SXJS3018




















Reviews: