Sunshine SXJS3018 Manual Download Page 14

 

                                                               

 

 

- 12 - 

SXJS3018 DOUBLE-DECK SCISSOR LIFT 

 

 

Chapter 9. Common Breakdowns and Solutions 

Breakdowns 

Reasons 

Solutions 

1.The  engine  works, 
but no pressure. 

1.No oil in the pump. 
2.The filter net is 
jammed. 
3.There is air in the 
pipelines or connec- 
tions.  The  overflow 
valve leaks. 

1. Infuse enough hydraulic oil. 
2. Clean out the dirty things. 
3. Exhaust, fasten the leaking 
connection or change the 
overflow valve washer. 

2.No power 

The engine is revers- 
ed or lack of phases. 

Check three phase four line 
powers. 

3.Correct  descending 
procedure, 

but 

no 

response. 

The control valve is 
jammed. 

Disconnect the control valve 
and clean it. 

4.The mechanical 
lock cannot open. 

1. Damage on the air 
cylinder. 
2. Damage on the 
Electromagnetic 
valve. 

1. Check the air cylinder. 
2. Check the gas-controlled 
electromagnetic valve. 

5. No lifting. 

1. Something wrong 
with the button. 
2.The electromagne- 
tic valve doesn

t work. 

3. The control valve 
Is jammed. 

1. Check or change the 
button. 
2. Check the electromagnetic 
valve and the relative lines 
3. Clean it. 

6.  There  is  pressure 
in 

the 

hydraulic 

system, but it is under 
20Mp.  It  cannot  lift  a 
car. 

1.Seals of the Non- 
return Valve or Over- 
flow Valve are invalid. 
2. Lack of hydraulic 
oil. 

1. Check the seal circle of the 
Non-return Valve or Overflow 
Valve, and the inner tie-in of 
hydraulic box. 
2. Infuse hydraulic oil. 

7.  Shaking  and  hard 
to adjust the height. 

There is air in the 
hydraulic loop. 

Raise the cylinder to the 
highest  and  the  assistant  to 
the lowest, dismantle the pipe 
connections to exhaust. 

8.Heavy  car  cannot 
be lifted. 

Lack of pressure. 

The Common pressure is 
18Mp. Adjust the system 
pressure  to  21Mp  for  the 
heavy  cars,  and  restores  it 
after getting down. 

9.The  Button  doesn

work. 

There is open circuit. 

Check that if the circuit ends 
becomes loosen. 

10.The insurance 
doesn

t work. 

There is short circuit. 

Check 

that 

if 

there 

is 

short-circuit in circuit. 

Summary of Contents for SXJS3018




















Reviews: