Sungrow SG2K5TL User Manual Download Page 4

Page: 4 / 80

Symbols Explanation

Important instructions contained in this manual should be followed during installation,
operation and maintenance of the inverter. And they will be highlighted by these
symbols.

DANGER indicates a hazard with a high level of risk which, if not avoided, will
result in death or serious injury.

WARNING indicates a hazard with a medium level of risk which, if not avoided,
could result in death or serious injury.

CAUTION indicates a hazard with a low level of risk which, if not avoided, could
result in minor or moderate injury.

NOTICE indicates a situation which, if not avoided, could result in equipment or
property damage.

NOTE indicates additional information, emphasized contents or tips to help you solve
problems or save time.

Summary of Contents for SG2K5TL

















































































Search results

Summary of Contents for SG2K5TL

Reviews:

Related manuals for SG2K5TL

Brands by name

Popular brands

Sungrow SG2K5TL, User Manual

Search results

Summary of Contents for SG2K5TL

Reviews:

Related manuals for SG2K5TL

Brands by name

Popular brands