Sungrow SG2K5TL-S User Manual Download Page 63 | Manualshive

Page: 63 / 86

background image

User Manual

9 Troubleshooting and Maintenance

55

9.1.2 Troubleshooting of Faults in the smartphone application
interface

When faults occur, “Fault” state can be shown in the smartphone application
interface.

Fault
Code

Description

Troubleshooting

002

The grid voltage exceeds
inverter allowable upper
limit.

1. Check the voltage of the grid.
2. If the grid voltage exceeds the permissible
range of inverter protection parameters, ask
utility grid company for solution.
3. If the grid voltage is within the permissible
range, contact Sungrow Service Dept..

003

Grid transient voltage
exceeds the permissible
range

1. This is a short-term fault due to grid
condition. Wait a moment for inverter recovery.
2. If the fault still exists, please contact
Sungrow Service Dept..

004

The grid voltage is below
inverter’s allowable lower
limit.

1. Check the grid voltage.
2. If the grid voltage exceeds the permissible
range of inverter protection parameters, ask
utility grid company for solution.
3. If the grid voltage is within the permissible
range, contact Sungrow Service Dept..

005

The grid voltage is too
low.

1. This is a short-term fault due to grid
condition. Wait a moment for inverter recovery.
2. If the fault still exists, please contact
Sungrow Service Dept..

006

The AC output current
exceeds inverter
allowable upper limit.

1. The inverter will resume if the output current
falls below the protection value.
2. If the fault still exists, please contact
Sungrow Service Dept..

007

Transient AC overcurrent

1. The inverter will self-recover after several
seconds.
2. If the fault still exists, please contact
Sungrow Service Dept..

008

The grid frequency
exceeds inverter
allowable upper limit.

1. Check the grid frequency.
2. If the grid frequency exceeds the permissible
range of inverter protection parameters, ask
utility grid company for solution.
3. If the grid frequency is within the permissible
range, contact Sungrow Service Dept..

009

The grid frequency is
below the inverter
allowable lower limit.

«
...
61
62
63
64
65
...
»

Summary of Contents for SG2K5TL-S























































































Reviews:

No comments

Related manuals for SG2K5TL-S

Brand: OT Systems Pages: 16

Brand: Somogyi Elektronic Pages: 10

Brand: Microchip Technology Pages: 56

Brand: B&B Electronics Pages: 3

Indigo ADDEC-210

Brand: Crystal Vision Pages: 37

Brand: Asian Electron Pages: 16

FRENIC-Multi FRN0.1E1S-2LM1

Brand: Fuji Electric Pages: 33

Brand: Motrona Pages: 16

Brand: SIIG Pages: 32

Brand: Davis Instruments Pages: 24

Brand: Weco Pages: 56

Brand: Tascam Pages: 28

Brand: Hall Research Technologies Pages: 8

4i4o + Merge 2i4o

Brand: Prodipe Pages: 16

Brand: Kohler Pages: 88

Brand: Kisae Pages: 12

Brand: Federal Signal Corporation Pages: 56

Brand: Philips Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands