manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000E, Installation Manual

Share
Download
Sun Microsystems SPARCcenter 2000E Installation Manual Download Page 53

Reader Comments

We welcome your comments and suggestions to help improve this manual. Please let us
know what you think about the SPARCserver 2000E Power Supply Installation Manual,
part number 802-2700-10.

■

The procedures were well documented.

Strongly

Strongly

Not

Agree

Agree

Disagree

Disagree

Applicable

❑

❑

❑

❑

❑

Comments

■

The tasks were easy to follow.

Strongly

Strongly

Not

Agree

Agree

Disagree

Disagree

Applicable

❑

❑

❑

❑

❑

Comments

■

The illustrations were clear.

Strongly

Strongly

Not

Agree

Agree

Disagree

Disagree

Applicable

❑

❑

❑

❑

❑

Comments

■

The information was complete and easy to find.

Strongly

Strongly

Not

Agree

Agree

Disagree

Disagree

Applicable

❑

❑

❑

❑

❑

Comments

■

Do you have additional comments about the SPARCserver 2000E Power Supply
Installation Manual?

Name:

Title:

Company:

Address:

Telephone:

Email address:

Summary of Contents for SPARCcenter 2000E























































Reviews:

No comments

Brands by name

Popular brands

Load more brands