manualshive.com logo in svg

Sun Microsystems SPARCcenter 2000E, Installation Manual

Share
Download
Sun Microsystems SPARCcenter 2000E Installation Manual Download Page 34

2-18

SPARCserver 2000E Power Supply Installation Manual—April 1995

2

2.5.2.6 Power Supply Sense Cable

1. Remove the jumper-connector from the power supply adapter board.

You will find this device plugged into the connector nearest the outside
edge of the cabinet. Remove it. See Figure 2-18.

2. Plug the sense cable for the bottom power supply into the power supply

adapter board.
Plug it into the near-most connector — from which the jumper-connector
was removed in Step 2.

3. Plug the other end of the sense cable into the sense connector on the

bottom power supply.
Plug it into J1 near the top of the supply.

Figure 2-18 Removing the Jumper-Connector and Installing the Sense Cable

Power supply
adapter board

Jumper connector: Remove to allow the
lower power supply cable sense cable to be
plugged into this connector.

Power supply sense cable
for bottom power supply

Summary of Contents for SPARCcenter 2000E























































Reviews:

No comments

Brands by name

Popular brands

Load more brands