background image

 Page 4 

 

Introduction  

Safety  

Precautions when assembling a greenhouse:  
The  wearing  of  protective  gloves  and  stout  footwear  is  essential  when  handling  glass  and  recommended  even  for 
Polycarbonate which does not shatter but has sharp edges.  
Protective goggles are recommended whilst handling glass and the glazing spring clips.  
Assembly of the greenhouse frame is much easier with two people and essential for glazing with glass.  

 

Site selection:  

Choose a site in maximum light, ideally with no direct shade.  
Avoid  overhanging  trees  as  much  as  possible  as  leaves  will  make  regular  cleaning  necessary  and  broken  branches  are  a 
potential hazard.  
Small trees, bushes or fences nearby can be helpful, acting as a wind break.  
A  position  close  to  the  house  will  make  access  easier  for  watering  and  tending  plants  and  also  make  it  easier  to 
supply power cables or automatic watering systems if required.  

Site selection & preparation:  

The  site  must  be  prepared  so  that  the  base  of  the  greenhouse  is  level  all  round  and  checking  with  a  spirit  level  is 
required.  

Base options & construction:  

The  use  of  our  purpose-made,  galvanised  steel  base  is  recommended.  They  are 
made to fit these greenhouses.  
It is easier to maintain a level and square foundation.  
They are easy to install, requiring little expertise: full instructions are included in the pack.  
 
Bases can also be constructed from bricks, blocks, or mounted on a concrete pad.  
The  bricks  or  blocks  should  be  cemented  onto  firm  and  level  concrete  footings  and  the  greenhouse  frame  drilled  and 
screwed to the base. Fig3.  
If  a  concrete  pad  is  made,  it  is  important  that  this  slopes  away  from  buildings  and  walls  to  prevent  water  damage. 
Time must be allowed for any concrete or cement to dry before mounting the greenhouse.  
 
The base must be square or the greenhouse will be distorted. A=A Fig1 & B=B Fig2.  
The  greenhouse  must  be  firmly  fixed  to  the  ground  and  to  the  wall:  the  base  should  be  constructed  and  installed 
before the greenhouse assembly is undertaken.  

Fig2  

Fig1 

A = A 

When the diagonal  

measurements are equal, 

the base will be square.  

 

A  

 

 

 

Greenhouse  
Frame 

Screw & Plug 

 

Batten  

 

Fig3  

 

Brick base  

 

Concrete pad  

 
 
 
 

For sales advice before you buy phone Summer Garden Buildings free 7 days a week on 0800 9777828

Summary of Contents for Lean-to Greenhouse













Reviews: