Summer Fun Pool Bubble, Customer'S Manual

Page: 11 / 26

E N G L I S H
Nome file:
File name:
LIBRETTO ISTRUZIONI - MGR10009 - Angolo relax.doc Rev. 0 28/12/2010
Pagina 11-di 26
If taking drugs that induce drowsiness (i.e.: tranquillizers, antihistamines or anticoagulants), avoid swimming in heated pools .
Prolonged immersion in hot water may cause hyperthermia
4,
while immersion in cold water may cause hypothermia
5
, with symptoms such as: Dizziness,
fainting, drowsiness, lethargy
6
. Consequences of hyperthermia and hypothermia may be: Unawareness of imminent danger, lack of heat or cold perception,
failure to recognise the need to exit the pool , physical inability to exit the pool , damages to foetus for pregnant women, unconsciousness with consequent
drowning risks.
3. Product presentation.
3.1. Product scope.
The product was designed to be able to transform your pool into a "spa" pool . It is easily adaptable to all pools .
3.2. Composition.
See Fig. 3 .
# #
1
Air hose ( hydraulic component )
from the blower to the check valve
(length X [m])
7 Check valve
2 Hose clamp 8 Air hose support
3 Bayonet connector 9 Air flow plug
4 Bayonet adapter 10 Air diffuser
5 O-ring 11
Air hose (
hydraulic component
)
from the check valve to the air diffuser
(length X [m])
6 Blower 12 Pool (not supplied with the product)
Tab. 3.
4. Technical specifications and features.
See Tab. 1 in Fig. 1 .
5. Installation.
5.1. Necessary tools.
See Fig. 4 .
5.2. Storage features and conditions.
Store the product in a dry place and keep away from the elements.
Storage temperature: -20 [°C] to +40 [°C].
5.3. Transport.
The product is delivered suitably protected against transport damages. However, handle with care to avoid damages.
5.4. Handling.
Be careful when handling the product (air diffuser – Fig. 3 , # 10 - full of sand) since extremely heavy.
5.5. Positioning.
The product ( blower, Fig. 3 , # 10) must always be at least 3,5 [m] from the edge of the pool ( Fig. 5 ), and out of the pool .
The product (air diffuser, Fig. 3 , # 10) must be placed on the bottom of the
pool
.
Considering the following aspects is recommended:
•
Dimensions and position of hydraulic components .
•
Necessary clearance.
•
Power cord position (
blower
).
•
Location of the power supply ( electrical socket ).
•
Support and its location.
Make sure the product is positioned in a place where noise generated during normal operations does not create disturbances.
Position the product is a shady area to avoid overheating the blower .
5.6. Connections and start-up.
The product must be installed and operated by individuals with appropriate training.
The electrical system must meet current international and/or national regulations.
The product must be connected to an
power outlet equipped with a residual current device with sensitivity over 30 [mA]. Before starting the product make
sure this device is installed in your electrical system. Contact a technician if necessary.
Make sure the product complies with your electrical system.
The power outlet must be at a suitable distance from the water but easily accessible in order to be able to easily turn off the product in the event of fault.
Cutting the power cord and/or replacing the power plug is strictly prohibited.
The power cord must be positioned to avoid possible damages such as bends and/or cuts.
5.6.1. Filling the air diffuser.
Proceed as follows:
1. Fill the air diffuser (
Fig. 3 , # 10) with sand (not included, about 13.5 [kg]), as illustrated in Fig. 6.
2. Submerge the air diffuser under the water surface and drain air.
3. Keeping the diffuser submerged, close with plugs (
Fig. 3 , # 9).
5.6.2. Hose connection.
Proceed as follows:
1. Place the o-ring ( Fig. 3 , # 5) on the blower air outlet ( Fig. 3 , # 6).
2. Screw in the bayonet adapter ( Fig. 3 , # 4) on the
blower
air outlet ( Fig. 3 , # 6).
3. Connect the bayonet connector ( Fig. 3 , # 3) to the air hose ( Fig. 3 , # 1) and secure it with the hose clamp ( Fig. 3 , # 2).
4. Place the air hose ( Fig. 3 , # 1) in the air hose support ( Fig. 3 , # 8) as indicated in Fig. 7 .
5. Connect the air hose ( Fig. 3 , # 1) to the check valve ( Fig. 3 , # 7) and secure it with the hose clamp ( Fig. 3 , # 2), making sure it permits air flow in the correct
direction, Fig. 8 .
6. Connect the air hose ( Fig. 3 , # 11) to the check valve ( Fig. 3 , # 7) and secure it with the hose clamp ( Fig. 3 , # 2).
7. Connect the air hose ( Fig. 3 , # 11) to the air diffuser ( Fig. 3 , # 10) and secure it with the hose clamp ( Fig. 3 , # 2), see Fig. 10 .
8. Position the air hose as indicated in Fig. 9 .
9. Position the air diffuser inside the pool ( Fig. 3 , # 12).
The check valves should be placed outside the pool and over the water level ( Fig. 2) .
4
Increase in body temperature over physiological limits, maximum limit 37 [°C].
5
Decrease in body temperature over physiological limits, minimum limit 35 [°C].
6
State of inactivity or lack of reactivity that nears unconsciousness.