SUHNER ABRASIVE UWK 10-R125, Technical Document

Page: 20 / 44

1.1 g
enerAl notes on sAfety
This operation manual is applicable for the machines
UWK 10-R125, UWK 10-R150. The machines may only be
handled by personnel who are qualified.
Hold power tools by insulated gripping surfaces when
performing an operation where the cutting tool may con-
tact hidden wiring or its own cord. Contact with a «live»
wire will make exposed metal parts of the tool «live» and
shock the operator.
WARNING Read all safety warnings and all in-
structions.
Failure to follow the warnings and in-
structions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
1.2 u
se of the mAchine for purposes for
which it is intended
The machines are intended for the purpose of cutting,
roughing and brushing of metal and stone materials with-
out the use of water.
1.3 i
ncorrect use
All uses other than those described under section
1.2 are regarded as incorrect use and are there-
fore not admissible.
1.4 ec
declArAtion of conformity
Otto Suhner GmbH of Trottäcker 50, D-79701 Bad Säck-
ingen, hereby declares under sole responsibility that the
product with the serial or batch no. (see reverse side) com-
plies with the requirements under the Directive 2014/30/
EU, 2006/42/EC, 2011/65/EU. Applied standards: EN ISO
12100, EN 60745, EN 55014-1, EN 55014-2, EN 61000-3-
2, EN 61000-3-3. Document Agent: M. Voyame. D-Bad
Säckingen, 06/2017.
M. Voyame/Division manager
2. c
ommISSIonIng
2.1 p
rior to tAKing the mAchine into serVice
Before connecting tool to a power
source, be sure the voltage sup-
plied is the same as specified on
the name plate of the tool. The power sup-
ply should not vary more than 10% above or below the
voltage indicated on the nameplate. Check grinding tool
prior to use. The grinding tool must be mounted centrally
and positioned against the limit stop. The maximum al-
lowable speed of the tool and of the chuck may not be
1. n
oteS on
S
afety
exceeded under any circumstances. Observe national
regulations. Remove safety guard. Take protective meas-
ures when dust can develop during working that is harm-
ful to one’s health, cumbustible or explosive. Wear a dust
mask and work with dust/chip extraction when connecta-
ble.
2.2 t
AKing the mAchine into serVice
Preselect speed with adjusting wheel according to speed
table.
Level 1: 4200 min
-1
Level 4: 7600 min
-1
Level 2: 5200 min
-1
Level 5: 8800 min
-1
Level 3: 6400 min
-1
Level 6: 10‘000 min
-1
During operation never exceed the speed which
has been matched to the grinding tool specifica-
tions!
2.2.1 t
unr on
/t
urn off
The switch must be in the OFF position. To turn the ma-
chine on, push the ON/OFF switch toward the front unteil
it clicks in. Press the ON/OFF swith to trigger the blocking
and the machine shuts down.
2.3 r
Ating dAtA
Power voltage 120/230/240V, 50/60Hz
Power Input 230/240V 1530W
Power Output 230/240V 1000W
Power Input 120V 1340W
Power Output 120V 800W
No-load speed UWK 10-R125 10‘500 min
-1
No-load speed UWK 10-R150 10‘000 min
-1
Max. tool Ø UWK 10-R125 125mm
Max. tool Ø UWK 10-R150 150mm
20
P
ortugúes
Español
Italiano
English
F
rançais
Deutsch
English