background image

Page 6

7-17

#7031931 - Revision A - June, 2014

UNDER COUNTER SERIES

UNDER COUNTER SERIES

(SWS #3603000)

(SWS #3603000)

Component Removal

Shelf Ladders (Model UC-24C)

The shelf ladders are attached to the side walls with
screws.

To remove a shelf ladder, first remove the refrigerator
liner cover.  Then, extract the shelf ladder mounting
screws and pull the shelf ladder away from side wall
and out of compartment.  (See Figure 7-40)

Compartment Light Bulb & Socket (Model UC-24C)

The compartment light bulb and socket are in the ceil-
ing of the compartment.  Tabs at the back of the socket
hold it in the light bracket (See Figure 7-41).

Light Bulb Removal

Turn light bulb counterclockwise to remove it; clock-
wise to install it.

Light Socket Removal

Pull light socket from hole in bracket, then discon-
nect electrical leads.

NOTE: 

This may break the tabs on the back of the

socket, but since it should only be removed in order
to replace it, this should not matter.  If not removing
it in order to replace it, then drill out the heads of
the rivets holding the bracket in place, lower the
bracket down, then depress the tabs on the side of
the socket while pushing it out of the bracket.

Control Panel/Display Assembly (Model UC-24C)

The control panel/display assembly is attached at the
top front of the mullion assembly by screws passing up
from beneath the mullion into screw grommets that are
molded into the display assembly.  A wire cover is
attached to the bottom of the mullion assembly with
plastic rivets to protect the control cable.

To remove the control panel/display assembly, (See
Figure 7-42):

1.

Use a fingernail, putty knife, or similar device to
extract the plastic rivet center posts, then pull rivets
out and drop wire cover from bottom side of mullion
assembly.

2.

Disconnect display electrical leads at bottom side of
mullion assembly.

3.

With a phillips-head screwdriver, extract control
panel mounting screws.

4.

Lift assembly up, feeding wire leads up through
access hole.

Figure 7-42.  Control Panel/Display Assembly

Figure 7-40.  Shelf Ladder Removal

Figure 7-41.  Compartment Light Bulb / Socket

Light Socket

Light Bulb

Bracket

Shelf Ladders

Control
Panel
Assembly

Wire
Cover

Summary of Contents for Wolf UC Series














Reviews: