Studer VarioString VS-120 User Manual Download Page 56

Page: 56 / 64

Studer Innotec SA
VarioString

V 2.3

User manual

Level

User

ref. Parameter

Factory value

User

value

Expert 14124

Combination of the events for the auxiliary contact
(AUX 2)

Any (Function OR)

Expert 14126 Activated in night mode (AUX 2)

Expert 14127 Delay of activation after entering night mode (AUX 2)

1 min

Expert 14128

Activation time for the auxiliary relay in night mode
(AUX 2)

1 min

Expert 14130 VarioString is OFF (AUX 2)

Expert 14131 Battery undervoltage (AUX 2)

Expert 14132 Battery overvoltage (AUX 2)

Expert 14133 Earth fault (AUX 2)

Expert 14134 PV error (48h without charge) (AUX 2)

Expert 14135 Overtemperature (AUX 2)

Expert 14136 Bulk charge phase (AUX 2)

Expert 14137 Absorption phase (AUX 2)

Expert 14138 Equalization phase (AUX 2)

Expert 14139 Floating (AUX 2)

Expert 14140 Reduced floating (AUX 2)

Expert 14141 Periodic absorption (AUX 2)

Expert 14143 Battery voltage 1 activate (AUX 2)

Expert 14144 Battery voltage 1 (AUX 2)

46.8 Vdc

Expert 14145 Delay 1 (AUX 2)

1 min

Expert 14146 Battery voltage 2 activate (AUX 2)

Expert 14147 Battery voltage 2 (AUX 2)

47.8 Vdc

Expert 14148 Delay 2 (AUX 2)

10 min

Expert 14149 Battery voltage 3 activate (AUX 2)

Expert 14150 Battery voltage 3 (AUX 2)

48.5 Vdc

Expert 14151 Delay 3 (AUX 2)

60 min

Expert 14152 Battery voltage to deactivate (AUX 2)

54 Vdc

Expert 14153 Delay to deactivate (AUX 2)

60 min

Expert 14154 Deactivate if battery in floating phase (AUX 2)

Expert 14156

Contact activated with the temperature of battery
(AUX 2)

Expert 14157 Contact activated over (AUX 2)

3 °C

Expert 14158 Contact deactivated below (AUX 2)

5 °C

Expert 14159

Only activated if the battery is not in bulk phase
(AUX 2)

Expert 14161 Contact activated with the SOC 1 of battery (AUX 2)

Expert 14162 Contact activated below SOC 1 (AUX 2)

50 % SOC

Expert 14163 Delay 1 (AUX 2)

12 hours

Expert 14164 Contact activated with the SOC 2 of battery (AUX 2)

Expert 14165 Contact activated below SOC 2 (AUX 2)

30%

Expert 14166 Delay 2 (AUX 2)

0.2 hours

Expert 14167 Contact activated with the SOC 3 of battery (AUX 2)

Expert 14168 Contact activated below SOC 3 (AUX 2)

20%

Expert 14169 Delay 3 (AUX 2)

0 hours

Expert 14170 Contact deactivated over SOC (AUX 2)

90 % SOC

Expert 14171 Delay to deactivate (AUX 2)

0.2 hours

Expert 14172 Deactivate if battery in floating phase (AUX 2)

Expert 14173 Reset all settings (AUX 2)

Expert 14174 Block manual programming (dip-switch)

Summary of Contents for VarioString VS-120

































































Search results

Summary of Contents for VarioString VS-120

Reviews:

Related manuals for VarioString VS-120

Brands by name

Popular brands

Studer VarioString VS-120, User Manual

Search results

Summary of Contents for VarioString VS-120

Reviews:

Related manuals for VarioString VS-120

Brands by name

Popular brands