Strongway 46271 Owner'S Manual Download Page 9 | Manualshive

Page: 9 / 26

background image

9

7. Attach the pump assembly plate(18) to the right frame using bolts (19), washers (09), lock washers

(10) and nuts (11), then secure the pump assembly using screws (16) and washer (17). When this

step is complete insert the handle to the handle bracket.

8. Locate the hydraulic hose fitting on the cylinder and install the pressure gauge (33) to the pressure

gauge connection fitting, on the top of the hydraulic cylinder (31).

9. Tighten all bolts and screws.

«
...
7
8
9
10
11
...
»

Summary of Contents for 46271



























Reviews:

No comments

Related manuals for 46271

Brand: Dafra Pages: 4

BAE PS-XA-3Y-24-250-609-I

Brand: Balluff Pages: 48

Brand: ISC Pages: 38

Brand: Ryobi Pages: 20

PRO 8425 0206 30

Brand: Atlas Copco Pages: 64

Carlyle Tools 6-701A

Brand: Napa Pages: 16

Brand: Hadex Pages: 12

Brand: Integrated Power Designs Pages: 2

Brand: Elenco Electronics Pages: 8

Brand: Lutool Pages: 21

Brand: Meec Pages: 24

Brand: Magnaflux Pages: 28

Brand: C-TEC Pages: 2

Brand: SALKI Pages: 20

Meec tools 017401

Brand: Jula Pages: 30

Brand: HellermannTyton Pages: 4

Brand: MasterCraft Pages: 26

Brand: Makita Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands