Strongway 46271 Owner'S Manual Download Page 12 | Manualshive

Page: 12 / 26

background image

12

5. Pump the handle until ram nears work piece. Align work piece and ram to ensure center-loading.

Pump the handle to apply load onto work piece.

6. Align ram and work piece to ensure center loading.

7. When work is completed, stop pumping the handle. Slowly turn the release valve counter-clockwise

in small increments until ram is free from work piece.

8. Once ram has fully retracted, remove workplace from bed frame. Cautiously remove work piece from

press.

«
...
10
11
12
13
14
...
»

Summary of Contents for 46271



























Reviews:

No comments

Related manuals for 46271

Brand: Sanela Pages: 2

EnergyGrind-100

Brand: PEUGEOT Pages: 10

Brand: Wolf Garten Pages: 198

Brand: TorcUP Pages: 22

Brand: Paxton Pages: 3

Brand: Ingersoll-Rand Pages: 57

Brand: F.F. Group Pages: 48

CROSSOVER ANGLOCK VISE DX8

Brand: Kurt Pages: 21

Re-Bar-Tier RB397

Brand: Max Pages: 27

Brand: Mountz Pages: 2

Brand: MasterCraft Pages: 13

Martin 90357040

Brand: Harman Pages: 32

Brand: Bison Pages: 19

Brand: Hitachi Koki Pages: 37

Brand: Black & Decker Pages: 8

Brand: laguna Pages: 48

Brand: D-Link Pages: 16

Brand: D-Link Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands