Storm Century S-LSA Maintenance Manual Download Page 45

Page: 45 / 142

MAINTENANCE MANUAL

STORM Century S-LSA

STORM Century S-LSA

STORMAIRCRAFT

2.14 DAILY INSPECTION

Date Performed

by:

COCKPIT

01.

switch OFF

02.

battery ON

03.

fuel remote level indicator check

04. flaps

out

05.

trim on zero – free controls

06.

battery OFF

EXTERNAL CHECKS

01.

canopy integrity check

02.

bleedings: check fuel tank and filter

(before moving the aircraft)

03.

fuselage : check lower and upper side integrity – radio antenna - transponder antenna

04.

fin and rudder : check integrity and free movements

05.

Stabilator and tab - connections : check integrity and free movements

06.

nose wheel unit : check tire - integrity

07.

main landing gear : check tires – if pressure as required - brakes

08.

flap – right aileron : check integrity and free movement

09.

right wing leading edge – make sure there are no dents

10.

check if Pitot tube and statics are free

2. DAILY INSPECTION

Date Performed

by:

ENGINE COMPARTMENT

01.

remove upper cowling

02.

engine compartment free from foreign matters

03.

no liquid leaks

04.

check the unfixed or unbraked parts

05.

check oil level

06.

check cylinder head coolant level

07.

reassemble and fasten upper cowling

PROPELLER

01.

spinner and propeller : check fastening and integrity

02.

make sure the propeller blades have no notches nor scratches

EXTERNAL CHECKS, CONTINUED

01.

check if landing light fastened and intact

02.

engine cowling unit intakes: check if obstructed, clear if necessary

03.

left wing leading edge: make sure there are no dents

04.

aileron and flap : check integrity and free movement

Summary of Contents for Century S-LSA















































































































































Search results

Summary of Contents for Century S-LSA

Reviews:

Brands by name

Popular brands

Storm Century S-LSA, Maintenance Manual

Search results

Summary of Contents for Century S-LSA

Reviews:

Brands by name

Popular brands