background image

 

MAINTENANCE MANUAL 

STORM Century S-LSA 

 

STORM Century S-LSA  

 

STORMAIRCRAFT 

10. Application of Protective Treatments 

N/A 

11. Data: Relative to Structural Fasteners 

Antenna installation, removal and replacement should be in accordance with applicable 
provisions of AC43.13-1A and 43.13-2A. Also, refer to section 2.3 of Installation manual. 

12

Special Tools 

N/A 

13. This Section is for Commuter Category Aircraft Only 

A. 

Electrical loads: Refer to section 1.3 of this manual. 

B. 

Methods of balancing flight controls: N/A. 

C. 

Identification of primary and secondary structures: N/A. 

D. 

Special repair methods applicable to the airplane: Antenna installation, removal, and 

replacement should be in accordance with applicable provisions of AC43.13-1B and 43.13-2A. 

14. Overhaul Period 

No additional overhaul time limitations. 
 

15. 

Airworthiness Limitation Section 

N/A. 

 

16. Revision 

To revise this ICA, a letter must be submitted to the local FSDO with a copy of the revised 

FAA Form 337, and revised ICA. The FAA inspector accepts the change by signing Block 

3 and including the following statement: 

 
"The attached revised/new Instructions for Continued Airworthiness (date 

) for the above 

aircraft or component major alteration have been accepted by the FAA, superseding the 
Instructions for Continued 
Airworthiness (date _______)." 

17. 

Assistance 

Flight Standards Inspectors have the resources to respond to questions regarding 

the ICA. 

Implementation and Record Keeping 

For major alterations performed in accordance with FAA field approval policy, the owner/operator 
operating under Part 91 is responsible for ensuring that the ICA is made part of the applicable 
section 91.409 inspection program for their aircraft. This is accomplished when a maintenance 
entry is made in the aircraft's maintenance record in accordance with section 43.9. This entry 
records the major alteration and identifies the original ICA location (e.g., Block 8 of FAA Form 337, 
dated ________________________________ ) along with a statement that the ICA is now part of 
the aircraft's inspection/maintenance requirements. 

 
 
 
 
 

Summary of Contents for Century S-LSA















































































































































Reviews: