STORK TRONIC ST552 Glass Manual Download Page 18

Page: 18 / 23

Order number: 900350.011

V2.70

Seite 18

Error and warning messages

Display

Cause

Remedy

Sensor error
(Heating relay and analogue output are switched
off!)

Check sensor

Ptc

Sensor error on compensation element for
thermocouple measurement (P91=1,2)

Repair of controller

UEb

Overtemperature at E2 (P35=0, P52=1)

-----

Hot

Overtemperature at E2 (P35=1, P52=1)

-----

FAt

Alarm of the LowFat or NoContact control
settings

Check oil level and/or switch on/off
by pressing OFF button

Error in parameter memory

Repair of controller

OIL
control active

Warning message, fat operating time is
exceeded (see P82)

Acknowledge with the temperature
DOWN key

OIL
control blocked

Control is blocked,, fat operating time is
exceeded (see P82)

Acknowledge with the MELT and
START key

rES

Reset of fat operating time (see P86)

-----

Display flashing

Threshold alarm (P25=1)

-----

Timer lamp
flashing

Timer has elapsed (see P27 and P29)

Acknowledge with the DOWN key

Lamp "HEAT"
flashing slowly

Burner fault (see P58)

Switch on/off by pressing OFF
button

Lamp "HEAT"
flashing quickly

Burner restart chance (see P58)

Switch on/off by pressing OFF
button

„- - -“ flashing
during setup

Button lock (P19=1)

-----

Summary of Contents for ST552 Glass
























Search results

Summary of Contents for ST552 Glass

Reviews:

Related manuals for ST552 Glass

Brands by name

Popular brands

STORK TRONIC ST552 Glass, Manual

Search results

Summary of Contents for ST552 Glass

Reviews:

Related manuals for ST552 Glass

Brands by name

Popular brands