background image

12

866-795-1586 • WWW.STONEAGETOOLS.COM

REMOVE ROLLERS IN ABX-PRO TRACTOR

The standard roller size on the ABX-PRO Tractor is 

Ø.46 IN.

 The 

PROP-DBP accessory comes with a set of 

Ø.54 IN. 

replacement 

rollers to accommodate 8/4 hose. 
The replacement rollers must be installed on the ABX-PRO 
Tractor before inserting it into the man way. This process will be 
typical for Poly Roller replacements on the ABX-PRO Tractor 
Assembly.

WARNING 

Always de-energize the system before servicing or replacing any 

parts. Failure to do so can result in severe injury and/or death.

Keep hands, hair, and clothing clear of rotating parts.

1.  Open the back cover of the ABX-PRO Tractor by pulling 

the top two Quick Release Pins in the outward direction. 

(Figure 1)

2.  Push the Adjustable Handle in the counterclockwise 

direction to loosen the CAM Lever. Push the CAM Lever in 
the counterclockwise direction, moving the indicator pin to 

“Disengaged”

.  

(Figure 2)

3.  Loosening the Cam Lever opens up the space between the 

Roller Assemblies.  

(Figure 3)

4.    Using a 1/4” Hex Key, remove the Screws, Roller Washers, 

Outer Hub Plates, and Rollers from the Idler and Drive Hubs.  

(Figure 4)

SUB-ASSEMBLY 1 (ABX-PRO, ROLLERS, COLLET BLOCK, AND GUIDE TUBE)

FIGURE 3

Idler Roller 
Assembly

Drive Roller 
Assembly

FIGURE 1

Quick

Release 

Pin (x2)

FIGURE 4

Roller (x2)

Idler hub

Drive hub

 Outer Hub 

Plate (x2)

Roller 
Washer (x2)

5/16” 

SHCS 

(x2)

Cam Lever

Indicator 

Pin

“DISENGAGED”

Adjustable Handle

FIGURE 2

Summary of Contents for PROPOSITIONER PROP-DBP

























































Reviews: