www.stobag.com
30
4.3.1) Memorisation of the intermediate position “I”
If an intermediate positions “I” has been memorised, the awning can be manoeuvred into the programmed position by pushing the
▼
and
▲
buttons of the transmitter together. Proceed as follows to memorise the intermediate positions:
1.
Move the shutter into the desired intermediate position “I” by means of the
▲
■
▼
buttons of a remote control.
2.
Keep
the
■
button pushed until a beep is heard (after about 5 seconds).
5s
3.
Release
the
■
button and push it again for another 5 seconds until 4 rapid beeps are heard.
5s
4.
Push
the
▼ ▲
buttons together until 3 beeps signal that the position has been memorised.
Table “A4”
Programming of the intermediate position “I”
Example
4.3.2) Cancellation of the memorised position
In order to modify the memorised positions, they must firstly be cancelled and then the new positions programmed again.
1.
Push and hold the
■
button of an already memorised transmitter until a beep is heard
(after about 5 seconds).
5s
2.
Release
the
■
button and push it again for another 5 seconds until 4 rapid beeps are heard.
5s
3.
Push
the
▲ ▼
buttons together until 5 beeps signal that the intermediate position has
been
cancelled.
Now the new intermediate position can be programmed (Table “A4”).
Table “A5”
Cancellation of the intermediate position “I”
Example
1.
Push and hold the
■
button of an already memorised transmitter until a beep is heard
(after about 5 seconds).
5s
2.
Release
the
■
button and push it again for another 5 seconds until 4 rapid beeps are heard.
5s
3.
Push
the
▲
button (if the automatic or manual programming has been performed) or the
▼
button (if the semi-automatic programming has been performed), until 5 beeps signal that
the “0” and “1” positions have been cancelled.
WARNING: After having cancelled the “0” and “1” positions the shutter will move in the hold-to-run mode and the new positions need to be
memorised (Table “A3”).
Table “A6”
Cancellation of the “0” and “1” positions
Example
4.4) Memory deletion
If you need to delete all the transmitter and the programmed operations, carry out the procedure shown in table A7.
The memory can be deleted:
• with a
non-memorized
transmitter starting from point A.
• with a
previously memorized
transmitter starting from point No. 1.
The following can be deleted:
•
only the memorized
transmitters, finishing at point No. 4
•
all data
(transmitters, sensor level, TTBUS address, etc.), completing the procedure until point 6.
Table “A7”
Memory deletion
Example
A.
Switch the motor off, activate the Step-by-Step input (by connecting the White cable
with the White/Black one) and keep it active until the end of the procedure.
B.
Power the motor and wait for the initial beeps.
1.
Press and hold down button
■
on a transmitter (about 5 seconds) until you hear
a beep; then release it.
2.
Hold down the
▲
button on the transmitter until you hear 3 beeps;
release
the
▲
button exactly during the third beep.
3.
Hold down button
■
on the transmitter until you hear 3 beeps;
release
button
■
exactly during the third beep.
4.
Hold down the
▼
button on the transmitter until you hear 3 beeps;
release
the
▼
button exactly during the third beep.
5.
To cancel everything:
Press
both
▲
and
▼
within 2 seconds
6.
Cancellation is confirmed by releasing buttons
▲
and
▼
on the first of the 5 beeps.
➡
➡
➡
PP
5s
MOVENO_DSRCE-V.indd 30
MOVENO_DSRCE-V.indd 30
9.2.2010 14:33:50 Uhr
9.2.2010 14:33:50 Uhr
Summary of Contents for MOVENO DSRCE-V
Page 9: ...9 D MOVENO_DSRCE V indd 9 MOVENO_DSRCE V indd 9 9 2 2010 14 33 36 Uhr 9 2 2010 14 33 36 Uhr...
Page 17: ...17 F MOVENO_DSRCE V indd 17 MOVENO_DSRCE V indd 17 9 2 2010 14 33 42 Uhr 9 2 2010 14 33 42 Uhr...
Page 25: ...I 25 MOVENO_DSRCE V indd 25 MOVENO_DSRCE V indd 25 9 2 2010 14 33 47 Uhr 9 2 2010 14 33 47 Uhr...
Page 41: ...E 41 MOVENO_DSRCE V indd 41 MOVENO_DSRCE V indd 41 9 2 2010 14 34 00 Uhr 9 2 2010 14 34 00 Uhr...
