33
2) Installation
Incorrect installation could cause serious injury.
Proceed as follows to prepare the motor:
1. Position the limit switch crown (E) on the motor (A) until it fits into
the corresponding limit switch ring (F); make sure that the two
grooves match. Push it into position as shown in Fig. 5.
2. Mount the drive wheel (D) on the motor shaft.
3. On MOVENO-Y fasten the drive wheel with the snap ring. On
MOVENO-Z fasten the drive wheel with the M12 nut and washer.
4. Fit the assembled motor into the winding roller until the crown (E) is fully inserted.
5. Finally, secure the motor head to the special support (C) with the spacer (if any), using the clips or split pin (B).
A:
MOVENO DSRC-E Tubular motor
B:
Fastening clips or split pins
C:
Support and spacer
D:
Draw lock ring
E:
Idle lock ring
F:
Idle
ring
2.1) Electrical connections
For motor connections, an omnipolar disconnecting
device with a 3 mm minimum distance between contacts
must be provided for disconnection from the mains power
supply (disconnecting switch or plug and socket, etc.).
Carefully follow all the connection instructions, if you
have any doubts do not make experiments but consult the
relevant technical specifications sheets which are also
available on the web site www.stobag.com.
An incorrect connection may be dangerous and cause
damage to the system.
The cable used for the electrical connections of the MOVENO DSRC-
E motors has 5 wires; 3 of the wires (yellow tag) are for the mains
power supply and 2 wires (violet tag) are for the command signals.
For the electrical connections see the diagram below. The connec-
tion devices are not supplied with the product.
www.stobag.com
GB
PIN¬CONNECTION¬WITH¬(IRSCHMANN¬34!+¬¬34!3¬¬
L
N
PE
3x1.5mm
2
LNPE
(230VAC / 50Hz)
5x0.75mm
2
3
2
1
4
1 2 3 4
1
3
PE
4
2
M1
~
1
3
PE
4
2
M1
~
1
3
PE
4
2
M1
~
1
3
PE
4
2
1
3
PE
4
2
1
3
PE
4
2
å
BLACKå
COMMONå6 å
å
BLACKå
STEPBY3Tå
å
å
44"53ååå
å
BROWNå
PHASEåå
å
BLUEå
NEUTRALå
0%å YELLOWGREENå EARTHå
PIN¬CONNECTION¬WITHOUT¬(IRSCHMANN¬34!+¬¬34!3¬¬
5x0.75mm
2
L
N
PE
3x1.5mm
2
LNPE
(230VAC / 50Hz)
M1
~
BLACKWHITEå
COMMONå6 å
WHITEå
STEPBY3Tå
å
44"53ååå
BROWNå
PHASEå
BLUEå
NEUTRALå
YELLOWGREENå EARTHå
With FRT
Without FRT
The MOVENO DSRC-E motors can be programmed with particular
functions to resolve specific problems:
• FRT: this function allows to retract the fabric by a programma-
ble measurement after the awning has been completely opened,
thereby eliminating the unsightly sagging of the fabric when the
awning is open. For further information see table A9.
MOVENO_DSRC-E.indd 33
MOVENO_DSRC-E.indd 33
1.12.2011 15:48:09 Uhr
1.12.2011 15:48:09 Uhr
