32
Safety measures and warnings
The present manual contains important safety instructions for
the INSTALLATION and USE of the product.
INSTALLATION:
Incorrect installation could cause serious injury. For this rea-
son, all installation instructions contained in the present manu-
al should be carefully followed during the working operations.
PRODUCT USE:
For the safety of persons, it is very important to follow these
instructions carefully in the everyday use of the product. Keep
this manual in a safe place for future reference.
The MOVENO DSRC-E series motors, versions MOVENO-Y Ø45 mm and
MOVENO-Z Ø58 mm, have been designed for the automation of rolling
shutters and awnings; any other use is considered improper and is pro-
hibited. These motors are intended for residential use. Maximum continu-
ous operating time is 4 minutes. When selecting the motor based on the
application requirements, the nominal torque and operating time shown in
the rating plate must be considered.
The minimum diameter of the tube on which the motor can be installed is
52 mm for MOVENO-Y with torque up to 35Nm, 60 mm for MOVENO-Y
with torque over 35 Nm and 70 mm for MOVENO-Z.
The motor must be installed by qualified technicians in compliance with
current safety regulations.
All unnecessary electrical cables must be removed before installation;
all mechanisms not required for motorized operation must be disabled.
If the motor is installed at a height below 2.5 m, all moving parts of the
motor must be protected. For awning applications, the horizontal clear-
ance between the fully open awning and any stationary object must be at
least 0.4 m.
The PVC power supply cable supplied with MOVENO DSRC-E motors is
ideal for external installation.
The tubular motor must not be subjected to crushing, impacts, falls or
contact with any kind of liquid. Do not perforate or drive screws into any
part of the tubular motor; see figure 1. The control switch must be fixed
in an easily visible location but away from moving parts and at a height
no less than 1.5 m. Do not modify any components unless such action is
specified in these instructions. Operations of this kind are likely to lead to
malfunctions. STOBAG disclaims any liability for damage resulting from
modified products.
For maintenance and repairs contact a qualified technician.
When the roller shutter or awning is in movement, make sure that there
are no persons within the movement range. Do not activate the awning if
work is being carried out close by, for example: window cleaning; in case
of automatic control, disconnect the power supply as well. Do not let chil-
dren play with the fixed control device and keep the remote controls out
of their reach. Check the balancing springs (if any) and the wear of cables
at frequent intervals.
If the slope of the awning is less than 25% or less than the
value recommended by the manufacturer it should be retracted
to avoid water pockets when it rains.
The rolling shutter could be damaged if used when ice has
formed.
Some of the programming phases can use the mechanical
stops of the roller shutter (caps and/or burglar-proof springs).
In this case it is necessary to select a motor with a torque that
is suitable for the application taking into consideration the
effective stress and avoiding excessively powerful motors.
The climatic sensors in the series SKIROSOL are not to be
considered safety devices that eliminate faults on the awning
caused by heavy rain or strong winds (in fact a simple power
failure would make automatic movement of the awning impos-
sible). The climatic sensors should be considered part of an
automation used to safeguard the awning and to facilitate
use.
STOBAG declines all liability for material damage caused by
atmospheric agents not detected by the sensors.
The MOVENO DSRC-E series motors, versions MOVENO-Y Ø45
mm and MOVENO-Z Ø58 mm, are electric motors equipped with
RPM reduction and terminating at one end with a shaft on which the
driving wheels can be mounted; see figure 2. The motor must be
fitted inside the winding tube, where it can raise or lower the roller
shutter or awning.
The control unit incorporated in the motor also has a high precision
electronic limit switch system that can constantly detect the position
of the rolling shutter.
The movement limits, awning open and awning closed (as well as
intermediate positions), can be programmed and the awning auto-
matically stops when these positions are reached. The electronic
limit switch can also compensate for possible stretching of the fabric
(“CAT” function) thereby guaranteeing the perfect closure of the box
and avoid sagging when opened.
The MOVENO DSRC-E motors can be programmed to activate the
reduction of the torque (RDC function) that decreases motor torque
by approximately 50% just before the awning closes completely to
prevent excessive stretching of the fabric. This function can be disa-
bled via a transmitter (see 4.3.2.) or by means of the special pro-
gramming units MA 2000 which enable selection of the reduction
on 3 levels: to approx. 50, 40 or 30% of the torque. The MOVENO
DSRC-E motors also features an “RDT” draw release function that
reduces the stretch of the fabric momentarily after the closing opera-
tion has been completed, to prevent prolonged stretching. The CAT,
RDC and RDT functions have been especially studied to simulate the
careful and meticulous behaviour of a person who opens and closes
the awning manually.
The MOVENO DSRC-E series motors incorporate a radio receiver
operating at a frequency of 433.92 MHz, with rolling code technol-
ogy that guarantees high levels of security. It is possible to memorize
up to 14 transmitters for each motor in the SKIMY series; see figure
3; that allow the remote control of the motors, or 3 wind and sun
radio sensors “SKIROSOL” which control the motor depending on
the weather conditions.
Optional wind, sun and rain sensors can be connected to the weather
sensors input that automatically activate the motor when the weather
conditions require.
1) Product description
www.stobag.com
MOVENO_DSRC-E.indd 32
MOVENO_DSRC-E.indd 32
1.12.2011 15:48:09 Uhr
1.12.2011 15:48:09 Uhr
