Still CX-M 10 Operating Instructions Manual Download Page 20

Page: 20 / 152

Introduction

Residual risks

Residual hazards, residual risks

Despite careful operation and compliance

with standards and regulations, not all risks in

using the truck can be entirely excluded.
The truck and all other system components

comply with current safety regulations. Even

when the truck is operated correctly and all

safety requirements are met, residual risks

exist.
Persons in an area near the truck must be

particularly cautious and ready to react imme-

diately in the event of a malfunction, incident

or breakdown.

WARNING

All persons near the truck must be informed of the

risks associated with the use of these trucks.
In addition, we draw attention to the safety regulati-

ons in this operating manual.

The risks can include:
• Release of fluids due to leaks and ruptured

lines and tanks etc .

• Risk of accidents when driving over difficult

ground such as gradients, soft or uneven

ground or in areas with poor visibility etc .

• Risk of falling or tripping when moving the

truck, especially on wet or icy ground or

near fluid leaks.

• Drive at a speed appropriate for the load

and ground conditions.

• The stability of the truck has been tested to

the latest standards. These standards only

take into account the static and dynamic

tipping forces that can be produced when

the truck is used according to the operating

requirements and rules. Risks arising from

improper use or incorrect operation that

results in tipping forces that may impact

stability cannot be excluded in extreme

cases.

• Loss of stability due to unstable or sliding

loads etc.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands