Still CX-M 10 Operating Instructions Manual Download Page 62

Page: 62 / 152

Operation

Driving

123

456

789

PRG

1044_501-004

1044_501-005

Driving, pedestrian operation with

tiller, slow approach with drive switch

– From the side, grip the handle (1) or (4) on

the tiller.

NOTE

The lift truck is switched on.

CAUTION

Take care when operating, especially if the user is

not familiar with using this function.

DANGER

Risk of crushing feet.
Do not use this function for turning.
This function is designed to maintain a straight line.
Proceed from the cockpit with very slight move-

ments.

NOTE

The traction switch (special equipment) (2)

or (3) on the tiller can be operated with either

hand. The speed is reduced; the tiller can

be used at any time to steer so that the truck

keeps going forward in a straight line. Always

use the traction switch carefully; the truck

reacts immediately to any given command.

Avoid jerky movements, braking or change of

direction. If the traction switch is pushed in for

quite a long time, a safety circuit immobilises

the truck. If this occurs, simply release the

traction switch and then activate it again.

Forward gear

– Press the upper part of the drive switch with

your thumb.

– The speed of the fork lift truck increases as

you push the traction switch further, up to a

limit of 6 km/h.

– When the traction switch is released, the

fork lift truck brakes electrically.

4 499 284 [EN]

Summary of Contents for CX-M 10

























































































































































Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands

Still CX-M 10, Operating Instructions Manual

Search results

Summary of Contents for CX-M 10

Reviews:

Related manuals for CX-M 10

Brands by name

Popular brands