Stihl FS 460 C Technical Information Download Page 9 | Manualshive

Page: 9 / 30

Stihl FS 460 C Technical Information Download Page 9

Technical Information 40.2010

Page 9

TI_40_2010_13_01_02.fm

3.6

Gearbox

3.6.1

Versions with standard drive tube and
long drive tube, see

b

4.4

A new, maintenance-free gearbox with a gearhead
angle of 35° is used for the series FS 460 C in the
version with a standard drive tube and long drive
tube.

Gearhead angle 35°

3.6.2

Version with short drive tube, see

b

4.4

A new, maintenance-free gearbox with a gearhead
angle of 25° is used for the series FS 460 C in the
version with a short drive tube and sawing
handlebars.

Gearhead angle 25°

3.7

New deflectors and limit stops

3.7.1

Versions with standard drive tube and
long drive tube, see

b

4.4

The optimal deflector is available for each
application:

1

Deflector for mowing heads,
Diameter of cutting circle: 480 mm

2

Deflector for grass cutting blades and brush
knives

3

Deflector for shredder blade

4

Limit stop 200 mm for circular saw blades

5

Limit stop 225 mm for circular saw blades

All new deflectors and limit stops are fastened with
3 screws secured against loss.

For details about the approved deflectors and limit
stops, see

b

5.1.

317TI012 KN

317TI013 KN

317TI014 KN

5

4

3

2

1

«
...
7
8
9
10
11
...
»

Summary of Contents for FS 460 C































Reviews:

No comments