background image

 17 West St., W. Hatfi eld, MA 01088 

|

 800.582.8423 

|

 413.247.3380 

|

 fax 413.247.3369 

|

 [email protected] 

|

 www.stiebel-eltron-usa.com

Simply the Best

INSTALLATION INSTRUCTIONS 

SOL 27 PREMIUM S & W COLLECTORS - 230016 & 230017

6.  Inulate the connection using the provided thermal 
insulation.

Inlet & Outlet Connection

The inlets & outlets are plug-in style connections identical to 
the inter-panel connections. The installation method is the 
same as the inter-panel connection.

Connector clip

Outlet connector

Inlet connector

1.  Insert the inlet/outlet connector into the collector 
connection on each end of the array. Make sure to insert the 
connection with a sensor well on the end of the array that 
you intend to be the hot side (the outlet of fl ow of the array).

2.  Fit the connecting clip at the junction between collector 

and plug-in connection.

3.  Secure the connecting clip by pushing down on the 
locking tab.

4.  Install the inlet of the collector array in the same 
manner.

Collector Sensor

The correct connection of the collector sensor is crucial to 
the correct function of the solar system.

1.   Secure the sensor lead.

2.  Connect the sensor lead to the controller. Be sure 
to properly insulate the sensor wire using standard 
procedures.

Lightning Protection

If the building has a lightning protection system, the 
collector casing, mounting frame and pipework must be 
connected to the existing lightning protection scheme.

Connect the collector to the lightning protection system 
using screw fi ttings. Use two stainless steel seft-tapping 
screws per collector.

1.  Pre-drill the holes. Position the drill holes on the lower 
part of the front of the collector in the area shaded in the 
following illustration. When drilling the holes, maintain a 
distance of at least 4 inches from the corner of the collector 
casing.

Summary of Contents for 230016



















Reviews: