background image

 17 West St., W. Hatfi eld, MA 01088 

|

 800.582.8423 

|

 413.247.3380 

|

 fax 413.247.3369 

|

 [email protected] 

|

 www.stiebel-eltron-usa.com

Simply the Best

INSTALLATION INSTRUCTIONS 

SOL 27 PREMIUM S & W COLLECTORS - 230016 & 230017

to field-supplied 
supplemental DHW 

heater (tankless or 

tank-type)

overflow 
container

domestic water 
supply

T

BC 1

BC 1

Fill & 

Drain 

Valve

Pressure Rel. 

Valve

P

1" twin 

nipples (2)

T

BC 1 = ball valve with 
integrated check & 

thermometer well

Fill & 

Drain 

Valve

Pressure 

Gauge & 

Valve

Pump 
(3-speed)

Fill & 

Drain 

Valve

Throttle and 

isolation 

valve

Flow Meter

S

Temperature Sensor 

T

Thermometer

Expansion 

Tank

Air Fill 

Valve

Disconnect 

Valve

Solar Collectors

S2

S3

T/S4

Solar 
Storage 

Tank

Coil-in-tank
Heat Exchanger

mixing 

valve

Ball valve

Pressure
& Temperature
Rel. Valve

*For more information on the pump station and storage tank, please refer to each individual installation manual.

S1

MV

MV

SOL 27 Premium Inlet/Outlet
with sensor

SOL 27 Premium Inter-panel Connector

S1

Tank connection kit

SE Flowstar Pump Station

Fill & 

Drain 

Valve

SOL 27 Premium Inlet/Outlet

Typical System Layout

Below is a schematic for a basic solar thermal system using 
Stiebel Eltron components. Specifi cs of this design may vary, 
depending on the demands of the job site.

Summary of Contents for 230016



















Reviews: