Project Checklist
Kit Contents
☐
Laser cut wood (11 Sheets - See inventory on following pages)
☐
Illustrated instruction manual - (No full size plans are required to build this model)
☐
1 - Pre-bent landing gear (0.075 in. dia.)
☐
1 - 1/8 in. x 1/4 in. x 24 in. length balsa stock (Fuselage Stiffeners)
☐
1 - 1/4 in. square x 12 in. length balsa stock (Leading Edge)
☐
1 - 1/4 in. square x 24 in. length balsa stock (Leading Edge)
☐
1 - 3/16 in. x 3/16 in. x 12 in. length balsa stock (Main Spar)
☐
1 - 3/16 in. x 3/16 in. x 24 in. length balsa stock (Main Spar)
☐
2 - 1/32 in. x 18 in. music wire (taped to back of wood brick)
☐
2 - 1/32 in. inside dia. x 12 in. length plastic pushrod housing
☐
3 - 1/8 in. x 3/16 in. x 24 in. length balsa stock (Turbulator Spars / Sub Spar)
☐
Large Hardware Bag (4 x 6 in.)
1 - 3/16 in. x 3 in. Hardwood Dowel (Landing Gear Lug)
1 - Tail Skid [DUB-853]
1 - 10mm Square Hardwood Motor Mounting Stick
1 - Basswood Elevator Joiner “E6” (laser cut from 1/8 in. basswood stock)
2 - Windshield support sticks “WSS” (laser cut 3/16 in. square. stock)
2 - 1/8 in. x 3 in. Hardwood Dowel (Wing Mounts)
2 - Micro Razor Control Horns and Back Plates [DUB-936]
6 - #32 Rubber Bands
☐
Small Hardware Bag (2 x 3 in.)
1 - 1 in. length of fuel tubing (EZ link retainer)
1 - #2 x 1/4 in. sheet metal screw (to secure motor)
2 - Mini E/Z Connectors [DUB-845]
2 - Micro E/Z Links [DUB-849]
2 - 3/16 in. Neo. Magnet
2 - Rubber Wheel Retainers
6 - Mini Rubber Bands (Landing Gear Retention)
MAIN GEAR WHEELS NOT INCLUDED
We suggest using #6 Trexler brand inflatable wheels [TRX-06]. You may substitute E-Flite
2.5” [EFLA225] or any 2.5” foam wheel if you prefer not to use the more nostalgic Trexlers.
SkyBuggy © 2010 Stevens AeroModel all rights reserved.
Page 3 of 30
Required Building Supplies and Tools
☐
1/2 oz. Medium CA Glue
☐
1/2 oz. Thick CA Glue
☐
1/2 oz. Thin CA Glue
☐
Hobby Knife with ample supply of #11 blades
☐
Sanding block with 400 and 600 grit paper
☐
Heat Gun and Covering Iron
☐
Small Needle Nose Pliers
☐
Wire Cutters
☐
1 in. x 6 in. length sticky back velcro
☐
3/4 in. wide clear tape
☐
1 Roll AeroLITE (solite)
☐
1 Roll AeroTRIM (solartrim)
☐
1/32, 1/8, and 3/16 in. Drill Bits
☐
Permanent Marker
Suggested Building Supplies
☐
Long sanding bar
☐
Razor Plane
☐
Low Tack Painters Masking Tape
☐
CA glue accelerator (kicker)
☐
CA glue de-bonder
☐
Balsa filler