Stevens AeroModel Dystraction backyard /Indoor F3A Manual Download Page 2

 

REQUIRED TO COMPLETE KIT: 

 

Kit Contents

 

‰

 

Rolled Computer Drawn Plan Sheets 

‰

 

Illustrated Instruction Manual 

‰

 

Laser Cut Balsa and Hardwood Parts Sheets  (See Parts Inventory Sheet) 

‰

 

1 - Clear Canopy 

‰

 

Large Hardware Bag  

 

 

 

 

 

 

 

2 - 1/32” x 12” Music Wire. 
2 - .047” x 5” Music Wire. 
1 - 3/32” x 4” aluminum tube. 
2 - 1/32” ID Plastic Tube 
4 - CA Hinge Material 
2 - GWS 1.5” Ultra light Wheel 
3 - Pull / Pull exit rings (Clear) 

 

Recommended Finishing Items

 

1. 

1 Roll of Solarfilm So-Lite, Nelson Lite, or Ultracote Lite – Iron on Film Covering. 

2. 

1 Pkg. Dubro Micro Pull/Pull 

DUB846

. One package of the Dubro Micro Pull/Pull will provide all the necessary 

hardware for the Rudder / Elevator / Aileron linkages.   You will use two of the 1/32” crimp within this package to 
retain the wheels.  The optional 1 Pkg. Dubro Micro E/Z links 

DUB849

 can be substituted simply by using Z-

Bends for each push/pull linkage. 

 

Suggested Radio Gear: 
 

1. 

4-5 Channel Transmitter (4ch using “Y” harness for ailerons) 

2. 

4 – 4.8g-5.4g Sub Micro Servos (Cirrus 5.4g /  FMA PS20 / E-Hobby HE-2003)  

3. 

1 – 4-5 Ch. Mini Receiver (8g) 

4. 

1 – 12” Servo Extension (for elevator servo) 

5. 

1 – Flight battery 7.4v Lipoly capable of 5-6A continuous discharge. 

 

Suggested Power Systems: 

 
Brushless Power Systems: 
 

‰

 

Astro Flight 010 14T Direct Drive System / GWS 7x3.5 HD Prop / 7.4v ETEC 700HP. 

‰

 

Astro Flight 010 14T Direct Drive System /  Graupner 5.5x4.3 Cam Slim / 11.1v ETEC 700HP. 

‰

 

Hacker A20-34S / Phoenix 10 ESC / APC 8x3.8 SF Prop / 7.4v ETEC 700HP. 

‰

 

Hacker A20-50S / Phoneix 10 ESC / APC 8x3.8 SF Prop / 11.1v ETEC 700HP. 

 

Conventional Brushed Power Systems: 
 

‰

 

GWS LPS RLC-C 4.8V (6:1) / 7x5 APC SF Prop / 2s1p Kokam 340. 

 
Other Items You Will Need: 
 

1. Thin 

(super 

glue) 

2. 

Five Minute Epoxy 

3. 

Poly Sheet Protector for Plans (Wax paper or Plastic Wrap will work in a pinch) 

4. 

Straight Edge Razor Blade(s) 

5. 

Coarse / Med / and Fine Grit Sand Paper 

6. Rat-Tail 

File 

7. 

Tape Clear and Masking 

8. 

Balsa Wood Filler 

9. 

Glass Cleaner Solution (Windex) 

 

 

© 2003 Stevens AeroModel.  

 

Page 2 of 20 

Summary of Contents for Dystraction backyard /Indoor F3A




















Reviews: