Stevens AeroModel BuzzBomb 400, Build Instructions

Page: 3 / 46

Project Checklist
Kit Contents
☐
Laser Cut Wood (16 Sheets See “Laser Cut Parts Inventory”)
☐ Build Instructions
☐
Computer Drawn Detail Sheet (11x17)
☐ Pre-Cut Acetate Windscreen
☐
Pre-Bent Wire Landing Gear (3/32 Spring Steel)
☐ Adhesive backed vinyl profile pilot figure
☐
2 - 0.032 in. x 18 in. wire (pushrods taped to back of wood brick) [*]
☐ 2 - 0.032 in. I.D. x 12 in. length nylon tubing (pushrod housing taped to back of wood brick) [2022]
☐ 5x8 Hardware Bag
1 - 3/16 x 3-3/4 in. Dowel [1025]
1 - Tail Skid (DUB853) [4023]
1 - Pair Du-Bro RC 2-1/2 in. Super Light Wheels (DUB250SL)
2 - Basswood Laser Cut Center Section Turbulator Spars W30 and W31
2 - Mini E/Z Connector (DUB845) [4021]
2 - Razor Control Horns and Retention Plates (DUB936) [4022]
6 - #32 Rubber Bands
☐
2x3 Hardware Bag (Placed within 4x6 Hardware Bag)
1 - 1 in. Silicone Tubing [4005]
1 - 1/8 in. x 2 in. Aluminum Tube
2 - 3/16 x 2 in. Dowel [1022]
2 - Micro E/Z Links (DUB849) [4017]
2 - 1/16 in. x 3/16 in. Neo-Magnets [4014]
2 - Rubber Wheels Retainers [4015]
4 - #2 x 3/8 in. Screws [3012]
4 - #4 Nylon Washers [3018]
Suggested Electronics and Other Equipment (Available at StevensAero.com)
☐
Transmitter with at least 3 channels
☐
Micro Receiver with at least 3 channels (4-6g)
☐
2 Hitec HS-55 servos
☐
SA Sport BL400 2200KV motor (SUPA2212-6)
☐
SA Sport 30A ESC (SUP30AESC)
☐
GWS 8x4 Propellor (GW/EP8040)
☐
Prop adaptor for 1/8 in shaft [EFLM-1930 or EFLM-1923]
☐
1 Pair Deans Ultra Plugs for Battery to ESC Connection (WSD1300)
Required Building Supplies and Tools
☐
1/2 oz. Thick CA Glue (PAAPT20)
☐
1/2 oz. Medium CA Glue (PAAPT03)
☐
1 oz. Thin CA Glue (PAAPT09)
☐
CA glue applicator tips (PAAPT21)
☐
CA glue accelerator (PAAPT15)
☐
Balsa filler (HCAR3401)
☐
Hobby Knife with ample supply of #11 blades
☐
Sanding block with 400 and 600 grit paper
☐
Heat Gun and Covering Iron
☐
Small Needle Nose Pliers
☐
1/2 in. wide clear tape (DUB916)
☐
3/4 in. wide self-adhesive Velcro (DUB348)
☐
Soldering Iron
Optional Building Supplies and Tools
☐
Modeling Clay for Ballast
☐
CA glue de-bonder (PAAPT16)
☐
Long sanding bar
☐
Masking Tape (Low tack blue painters tape)
Build Instructions April 15, 2014 !
(c) 2011 Stevens AeroModel all rights reserved. ! Page 3