manualshive.com logo in svg

Steris Basil 4700, Maintenance Manual

Share
Download
Steris Basil 4700 Maintenance Manual Download Page 125

4-7

764333-098

8.

Gasket should last for several inspection proce-
dures. When necessary, order replacement gas-
ket (P117951-568 and P117951-392) from STERIS.

9.

Re-energize washer utilities.

4.5  MONTHLY CLEANING PROCE-

DURES

WARNING  –   CHEMICAL BURN AND/OR EYE
INJURY HAZARD: Detergents are caustic and

can cause adverse effects to exposed tissues. Do
not get in eyes, on skin or attempt to swallow. Read
and follow the precautions and instructions on the
detergent label and in the Material Safety Data
Sheet (MSDS) prior to handling the detergent,
refilling the detergent container or servicing the
detergent injection pump. Wear appropriate Per-
sonal Protective Equipment (PPE) whenever han-
dling the detergent or servicing the detergent
injection pump and lines.

WARNING –  SLIPPING HAZARD: To prevent
slips, keep floor dry. Promptly clean up any

spills or condensation. If spilled liquids are deter-
gents or other chemicals, follow safety precau-
tions and handling procedures set forth on deter-
gent or chemical label/or Material Safety Data
Sheet (MSDS).

• Remove Hard Water Deposits From Chamber and

Accessories

NOTE:  Depending on hardness of water being used,
it may be necessary to remove hard water deposits
more often. Remove deposits from chamber and mate-
rial handling accessories whenever deposits become
visible.

1.

Open chamber door. If desired, place empty wash
cart(s) and accessories in chamber.

2.

Turn OFF detergent supply pump (optional or by
others).

3.

Pour 1 gal (3.8 L) of descaling liquid into cham-
ber sump. Exit chamber and close door.

4.

Press 

MANUAL

 touch pad to access Manual Con-

trol mode.

5.

Select and start 

PUMP & DRIVE

 function.

6.

Let washer run for 15 minutes, then press 

PUMP

& DRIVE

 touch pad.

7.

Once hard water deposits are removed, select
and start DRAIN function to drain descaler solu-
tion from sump.

8.

Manually fill and drain chamber sump again to
remove any residue.

9.

Press 

X

 touch pad to exit Manual Control mode

and turn ON detergent pump.

4.6  ROUTINE MAINTENANCE

WARNING –  ELECTRIC SHOCK AND/OR
BURN HAZARD: Disconnect all utilities to

unit before servicing. Do not service unit unless
all utilities have been properly locked out. Always
follow local electrical codes and safety-related
work practices.

WARNING  –   BURN HAZARD: Allow unit to
cool down before performing any service on

mechanical components and on piping. Compo-
nents and piping become very hot during opera-
tion.

4.6.1  Grease Exhaust Fan Bearings

Exhaust fan bearings must be greased once a week as
follows:

1.

Locate remote exhaust fan grease fittings (see
Figure 4-3).

2.

Apply a high temperature, water-resistant grease
(P117951-457).

NOTE: If a standard temperature grease is used,
fan bearings must be greased once at end of each
day.

Figure 4-3. Exhaust Fan Grease Fittings

Fittings

Summary of Contents for Basil 4700










































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands