Sterilor Sel Installation Instructions & Use & Care Manual Download Page 15

 

15

 

pool in order to reduce all or part of this dose.  
 
Reminder:  Always  switch  off  STERILOR  Sel 
before adding salt. 
 
Leave  the  filtration  system  to  operate  by 
directing  the  backflow  nozzles  downwards  to 
dissolve the salt better. 
 
 
Wait  for  the  salt  to  be  completely  dissolved 
before switching STERILOR Sel back on. 
Every time salt is added to the swimming pool, 
the device must be switched off for 24 hours, 
so that the salt dissolves completely. Carry out 
a  new  salt  analysis  after  24  hours,  and  add 
more if necessary. 

4.1.4 Stabiliser 

 
The level of stabiliser must be between 30 and 
50 mg/l (ppm). 

 

The  level  of  stabiliser  should  be  analysed  at 
the  beginning  and  in  the  middle  of  each 
season.  
 
Ask  your  installer  to  analyse  the  level  of 
stabiliser,  which  must  not  exceed  60  mg/l 
(ppm).  Above  this  concentration,  the  chlorine 
is consumed. 

 

The  stabiliser  helps  to  maintain  the  level  of 
chlorine produced by protecting it from being 
destroyed by UVs. 

4.2 Production setting 

4.2.1 Displaying and adjusting the 
production 

 

 
 
 
 
 
 

 

The  amount  of  Chlorine  produced 

depends  on  the  salt  level,  water  temperature 
and  quality,  and  the  device's  operating  time, 
i.e. the filtration time. 
 

The  consumption  of  chlorine  depends 

on  the  water  quality,  contamination  of  the 
pool, its level of use, the environment and the 
climatic conditions. 

 

Average operating settings, in water at 
25 °C and with 5g/l of salt: 
 

The settings recommended below must 

be  refined  depending  on  the  region,  the 
climatic  conditions  and  the  level  of  use,  and 
only regular monitoring will guarantee correct 
swimming  pool  treatment.  Standard  settings 
cannot  be  defined  because  each  pool  is 
specific due to its dimensions, its location and 
its level of use. 

 
 

Swimming pool 

volume 

Production 

percentage 

0 to 40 m3 

30-50 % 

40 to 60 m3 

50-80 % 

60 to 100 m3 

80-120% 

100 to 120 m3 

120 to 135% 

120 to 160 m3 

135 to 160 % 

 

4.2.2 Production percentage setting 
procedure 

Production is regulated by keeping the 

P  key  pressed  down  and  using  the  +/-  keys, 
and  the  percentage  increases  or  decreases  in 
5% increments over a 30 to 180% range. 
 
 
 
 
 
 
 
 

Held  
down 

Summary of Contents for Sel
























Reviews: