36
MIGGY 161
COD. 6908300020
STEL s.r.l.
– Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
TECHNICAL DESCRIPTION
ENGLISH
13) Regulate the friction of the wire feeder (a more accurate regulation will be
possible after a few tests).
14) Set the post-gas value with the screw potentiometer (ref. N°10 par. 5.1) .
15) Set the burn-back* value with the screw potentiometer (ref. N°9 par. 5.1) .
16) Turn the rotating selector to position MIG 2T or MIG 4T(ref. N°4 par. 5.1) .
2 times: in this mode the welding arc lights, with the wire in contact with the piece,
the moment the torch button is pressed and it goes out the moment the button is
released.
4 times: in this mode gas comes out (pre-gas) the moment the torch button is
pressed, the welding arc lights, with the wire in contact with the piece, the moment the
button is released; when it is pressed again, the arc goes out and more gas comes
out to cool the piece (the gas comes out the whole time that the button is pressed);
when the button is released the post-gas time begins, as set previously with the screw
potentiometer.
17) Set the welding voltage with the potentiometer (ref. N°6 par. 5.1)
18) Set the wire speed with the potentiometer (ref. N°5 par. 5.1) .
19) Switch on the machine, turning the switch on the front panel to “ON” position (ref.
N°.8 par. 5.1).
20) Proceed with welding.
5.6– PREPARING FOR MIG WELDING WITHOUT GAS
To use a special cored wire that allows welding without the use of gas, proceed as
follows:
1) Connect the earth cable to the positive socket (+) (ref. N°4 par. 5.1) of the
generator.
2) Insert the connector of the MIG torch in the centralised euro socket (ref. N°7 par.
5.1) and tighten the ring nut.
3) Check the position of the polarity changing cable, opening the side door: for MIG
welding with special CORED WIRE without the use of gas it must be in position "-".
Now proceed as in the instructions in the paragraph "PREPARING FOR MIG
WELDING WITH GAS", starting from point 5, ignoring point 13 and of course all the
references to gas coming out of the torch.
73
MIGGY 161
COD. 6908300020
STEL s.r.l.
– Via del Progresso n° 59 – 36020
Loc. Castegnero (VICENZA) - ITALY
TEL. +39 444 639525 (central.) – +39 444 639682 (comm.)
FAX +39 444 639641 – E-mail: stel @ stelgroup.it
http: www.stelgroup.it
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
a) KENNDATEN
Name, Anschrift des Herstellers
Art der Schweißmaschine
Identifizierung der Serien-Nummer
Symbol der Schweißmaschinenart
Bezug auf die Baunorm
b) SCHWEISSAUSGANG
Symbol des Schweißverfahrens
Symbol für Schweißmaschinen, die für den Einsatz in Umgebungen mit erhöhter Stromschlaggefahr geeignet sind
Schweißstromsymbol
Zugewiesene Leerlaufspannung (durchschnittliche Spannung)
Schweißstrombereich
Werte des Aussetzzyklus (in 10 Minuten)
Werte des zugewiesenen Schweißstroms
Konventionelle Spannungswerte bei Belastung
c) EINSPEISUNG
Symbol der Einspeisung (Phasenzahl und Frequenz)
Zugewiesene Speisespannung
Maximaler Speisestrom
Maximaler wirksamer Speisestrom (identifiziert die Leitungssicherung)
d) ANDERE MERKMALE
Schutzgrad (IP22).
5.2– BESCHREIBUNG DES TYPENSCHILDS
1
2
4
6
7
8
14
9
18
15 16
17
13
12
11
10
5
3
DEUTSCH
TECHNISCHE BESCHREIBUNG
