background image

05/13

Pub. No. 601-C

- 13 -

Owners Manual

Digital Commercial Control Package Operation

Models: HC-9 thru HC-24 with DCCP Control

     minute OFF mode during an “Off-Peak” daytime 

period. IMPORTANT: Due to possible code violations 
or damage to the building drainage system the hot 
boiling water exiting in this process may require a 
Blow-Down Tank. Consult with your licensed 
contractor. Blow-Down tanks may be purchased 
separately.

8)  Steam Control: The steam valve(s) are controlled 

according to the room temperature sensor(s) and the 
programmed mode. When the room temperature is 
lower than the set temperature by one degree the 
steam valve will turn on. When it reaches the set 
temperature it turns off. If for some reason the room 
temperature exceeds the MAX TEMP setting (of 
either room) by more than 10 degrees the Digital 
Command Center will turn off the generator until that 
room temperature drops to 1 degree below the set 
temperature.   

9)  Aroma Control: There are two aroma control relays 

(one for each room) located in the Command Module 
on the generator. These relays can be used with 
most aroma pumps available.  The relays are 
programmed to conserve aroma therapy oil. The 
relays are only on when the following conditions are 
met. The program for that room must be in the MAX 

mode, the steam valve for that room must be on and 
the temperature in that room must be above the IDLE 
setting. When all these conditions are met, then the 
aroma relays will energize.

10)  Fahrenheit and Celsius: The Fahrenheit or Celsius 

temperature can be selected by changing a jumper in 
the Command Module (CN112). When it is not 
connected (open circuit), it will be Fahrenheit. When it 
is connected, it will be Celsius. The Jumper must be 
switched with power off (See wiring diagram on page 
11).

11)  Reset Feature: If it is ever necessary to reset all the 

programs and start over press and hold the PROG# 
button and the lower MIN button for five seconds 
simultaneously. This will reset every setting in the 
Command Center. This process can also be used to 
unlock the control if the password is lost or forgotten.

Model

No.

Product

No.

KW

Volts/

Phase/

Amps

Shipping

Weight

HC-9

HC-12

HC-15

HC-18

Speci

fi

cations Chart

60900
60901
60902
60903
60904
61200
61201
61202
61203
61204
61500
61501
61502
61503
61504
61800
61801
61802
61803
61804
62400
62401
62402
62403
62404

9

12

15

18

24

Max.

Cu. Ft.

400

500

620

740

1000

240/1/38
208/1/43
240/3/22
208/3/25

480/3/11

240/1/50
208/1/58
240/3/29
208/3/33
480/3/15
240/1/63
208/1/72
240/3/36
208/3/42
480/3/18
240/1/75
208/1/87
240/3/43
208/3/50
480/3/22

240/1/100

208/1/115

240/3/58
208/3/67
480/3/29

Water

Inlet 

Steam

Outlet

Dimensions

21”x19”x25”

21”x19”x25”

21”x19”x25”

21”x19”x25”

21”x19”x25”

140 lbs.

150 lbs.

150 lbs.

150 lbs.

150 lbs.

1/2” NPT

1/2” NPT

1/2” NPT

1/2” NPT

1/2” NPT

3/4” NPT

3/4” NPT

3/4” NPT

3/4” NPT

3/4” NPT

Line

Fuse 

50
60
30
35
15
70
80
40
45
20
80
90
45
60
25

100

110

60
70
30

125
150

80
90
40

HC-24

Summary of Contents for HC-9

















Reviews: