background image

LIMITED WARRANTY

STEAMIST, INC. hereby warrants that its Steamist generators Models HC-9, HC-12, HC-15, HC-18, and HC-24 are free from all 
defects in workmanship and materials for one (1) year from the date of purchase.

This warranty does not extend to damage caused by improper or negligent installation or use, or for any repairs attempted by 
any person other than an authorized Steamist dealer and shall be limited to the repair or replacement of defective parts by 
STEAMIST or its authorized dealers. After the unit has been disconnected and returned to STEAMIST's plant or to one of its 
authorized dealers warehouses, said repairs shall be without charge if within ninety (90) days of the date of purchase. After the 
expiration of ninety (90) days for the duration of the limited warranty period, there shall be a reasonable charge for labor incurred 
in connection with the repair or replacement indicated above.

Freight: Within the first ninety (90) days and with prior company approval, Steamist will pay all freight charges on items covered 
under our warranty. Thereafter and until the end of the warranty period, and with prior company approval, the customer is 
required to ship freight prepaid to Steamist's factory and Steamist will then ship freight prepaid back to customer.

This is not a service contract and this warranty does no include regular maintenance, cleaning or periodic check-ups, which are 
the sole and exclusive responsibility of the purchaser and are required as a condition of keeping this limited warranty in full force 
and effect.

This warranty shall not become effective unless the attached registration of Warranty is completed and returned to STEAMIST 
within fifteen (15) days of the date of installation.

This warranty is non-transferable and shall extend only to the original purchaser who shall have been named in the Registration 
of Warranty.
This warranty is void if any of the following should occur:

1. If the serial number has been altered or removed.
2. If the product is modified in any manner which STEAMIST concludes after inspection affects the reliability of the 
product.
3. If the product has been repaired or serviced by anyone not specifically designated and authorized by STEAMIST.
4. If the product is damaged because it is not operated or installed in accordance with supplied instructions.

The sole responsibility of STEAMIST under this warranty shall be limited to the repair of the product or replacement thereof, 
including parts, in the sole discretion of STEAMIST INC. The consumer's sole remedy shall be such repair of replacement as is 
expressly provided herein and under no circumstances shall STEAMIST be liable for any loss or damage be it direct or conse-
quential arising out of the use or inability to use this product.

THE FOREGOING IS IN LIEU OF ALL OTHER WARRANTIES AND SPECIFICALLY EXCLUDES AND DISCLAIMS 
EXPRESS AND IMPLIED WARRANTIES OF MERCHANTABILITY OR OF FITNESS FOR PARTICULAR USE OF 
PURPOSE. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF 
AND NEITHER STEAMIST NOR ITS DEALERS ASSUMES OR AUTHORIZES ANY PERSON TO ASSUME FOR ANY 
OF THEM ANY OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH SAID EQUIPMENT.

No warranty whether express or implied is given or made with respect to any accessory supplied by anyone other than 
STEAMIST.

Purchaser acknowledges that no other representations were made to him or relied on by him with respect to the quality and 
function of the generators.

Model No. 

____________________ 

Serial No.

 ____________________ 

Date of Purchase 

____________________

05/13

Pub. No. 601-C

- 16 -

Owners Manual

East Coast Office: 25 E. Union Ave., East Rutherford, NJ 07073 • Tel: 800-577-6478 • Fax: 201-933-0746
West Coast Office: Tel: 800-355-6478 • Fax: 661-940-1617 

®

Summary of Contents for HC-9

















Reviews: