background image

39

limited warranty

State Industries, Inc., the warrantor, extends the following LIMITED WARRANTY to the owner of this water heater.

1.  THE TANK
 

If the glass-lined tank in this water heater shall prove upon examination by the warrantor to have leaked due to natural corrosion from potable water therein, 

during the first THREE years after initial installation, the warrantor will supply a complete new State water heater of equivalent size and current model.  

Some government agencies are requiring energy efficient standards for water heaters. In the event regulations prohibit sale of a model of equivalent size 

and construction, State Water Heaters will provide a model which complies with the regulations of your area, in which case the consumer will be charged 

the difference in price between the like replacement and the energy efficient model required. The warranty on the replacement water heater will be limited 

to the unexpired term of the original warranty.

2.  ALL OTHER PARTS
  If within ONE year after initial installation of this water heater, any part or portion shall prove upon examination by the warrantor to be defective in material 

or workmanship, the warrantor will repair or replace such part or portion at its option.

3.  CONDITIONS AND EXCEPTIONS
  This warranty shall apply only when the water heater is installed in accordance with local plumbing and building codes, ordinances and regulations, the 

printed instructions provided with it and good industry practices.  In addition, a temperature and pressure relief valve, certified by and officially sanctioned 

and recognized independent testing agency and approved by the American Society of Mechanical Engineers, must have been installed.

  a.  This warranty shall apply only when the heater is:

   

(1) used at temperatures not exceeding the maximum calibrated setting of its thermostat;

   

(2) used at water pressure not exceeding the working pressure shown on the heater;

   

(3) filled with potable water, free to circulate at all times and with the tank free of damaging water sediment or scale deposits;

   

(4) used in a non-corrosive and non-contaminated atmosphere;

   

(5) used with factory approved anode(s) installed;

   

(6) in its original installation location;

   

(7) in the United States, its territories or possessions or Canada;

   

(8) sized in accordance with proper sizing techniques for commercial and/or residential water heaters;

   

(9) bearing a rating plate which has not been altered, defaced or removed, except as required by the warrantor;

   

(10) used in an open system or in a closed system with properly sized and installed thermal expansion tank;

   

(11) operated with properly installed dirt leg;

   

(12) fired with the fuel for which it was factory built;

   

(13) fired at the factory rated input;

   

(14) operated with the inner and outer combustion chamber doors in place.

  b.  Any accident to the water heater, any misuse, abuse (including freezing or thermal expansion damage) or alteration of, any operation in a modified form, 

or any attempt to repair tank leaks will void this warranty.

  c.  This warranty is void if a device acting as a backflow prevention device (check valves etc.) is installed in the cold water supply the heater is connected 

to, unless an effective method of controlling thermal expansion is also installed at the heater(s) and operational at all times.  The relief valve installed 

on the heater is not an acceptable method.

4.  SERVICE AND REPAIR EXPENSES
  Under the limited warranty the warrantor will provide only a replacement water heater or part thereof.  The owner is responsible for all other costs.   Such 

costs may include but are not limited to:

  a.  Labor charges for service removal, repair or reinstallation of the water heater or any component part;

  b.  Shipping, delivery, handling, and administrative charges for forwarding the new heater or replacement part from the nearest distributor and returning 

the claimed defective heater or part to such distributor.

  c.  All cost necessary or incidental for any material and/or permits required for installation of the replacement heater or part.
5.  LIMITATIONS ON IMPLIED WARRANTIES
  Implied warranties, including the warranty of merchantability imposed on the sale of this heater under state law or local code are limited to one (1) year duration 

for the heater or any of its parts.  Some areas do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

6.  CLAIM PROCEDURE
  Any claim under the warranty should be initiated with the dealer who sold the heater, or with any other dealer handling the warrantor’s products.  If this is 

not practicable, the owner should contact:

 

u.s. customers 

canadian customers

 

A. O. Smith Corporation 

A. O. Smith Enterprises Ltd.

 

500 Tennessee Waltz Parkway 

P. O. Box, 310 - 768 Erie Street

 

Ashland City, TN 37015 

Stratford (Ontario)  N5A 6T3

 

Telephone: 1-(800)-323-2636 

Telephone: 1-(800) 265-8520

 

a.  The warrantor will only honor replacement with identical or similar water heater or parts thereof which are manufactured or distributed by the warrantor.

  b.  Dealer replacements are made subject to in-warranty validation by warrantor.
7. DISCLAIMERS
 

NO OTHER EXPRESS WARRANTY HAS BEEN OR WILL BE MADE IN BEHALF OF THE WARRANTOR WITH RESPECT TO THE MERCHANTABILITY OF 

THE HEATER OR THE INSTALLATION, OPERATION, REPAIR OR REPLACEMENT OF THE HEATER.  THE WARRANTOR SHALL NOT BE RESPONSIBLE 

FOR WATER DAMAGE, LOSS OF USE OF THE UNIT, INCONVENIENCE, LOSS OR DAMAGE TO PERSONAL PROPERTY OR OTHER CONSEQUENTIAL 

DAMAGE.  THE WARRANTOR SHALL NOT BE LIABLE BY VIRTUE OF THIS WARRANTY OR OTHERWISE FOR DAMAGE TO ANY PERSONS OR 

PROPERTY, WHETHER DIRECT OR INDIRECT, AND WHETHER ARISING IN CONTRACT OR IN TORT.

 

a.  Some areas do not allow the exclusion or limitation of the incidental or consequential damage, so the above limitations or exclusions may not apply to you.

  b.  This warranty gives you specific legal rights, and you may also have other rights which vary from area to area.

Fill in the following for your own reference.  Keep it. Registration is not a condition of warranty.  The model and serial number are found on the heater’s rating plate.
Model No. ________________________________ Serial No. _______________________________ Date Installed ________________________________
Dealer’s Name _________________________________________________________________________________________________________________
Dealer’s Address _________________________________________________________________________ Phone No._____________________________
City and State __________________________________________________________________________ Zip ___________________________________

KEEP THIS WARRANTY POSTED ADJACENT TO THE HEATER FOR FUTURE REFERENCE.

Summary of Contents for SHE 50 76N









































Reviews: